Ultra electronic ID Card Printer manual For USA only, Machine Noise

Page 4

For USA only

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, used, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION: Changes or modifications not approved by party responsible for compliance could void user’s authority to operate the equipment.

Machine Noise

Sound power level: less than 70 dB (A) according to DIN45635 part 19 (EN27779).

The measurements are to be made according to DIN 45635 part 2019 or EN27779, respectively.

3

Image 4

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not touch the power plug during electrical Storms Do not use a line voltage other than instructedDo not wet the machine with water Do not touch the machine with wet handsDo not use the machine while it has a fault Pull out the power plug before cleaning MachineHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Connecting with a host computer Set the BUS switchesSet-up Set the Scsi IDConnect the printer and IC unit Connecting the IC unit Sold separatelyConnect the IC unit with the host computer Connecting the power cord Plug the power cable into the printerCompact IC unit sold separately Connect the compact IC unit to the host computerInstalling the card stacker Mount the card stacker on the printerHang the stacker claw on the stacker receptacle Discharging the cardSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Setting the retransfer film Remove the retransfer film cassetteSetting the number of frames to be used When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteSetting cards Open the card trayCard bracket locks when it reaches the hole Inserting cards Unit can take about 300 0.76mm-thick cardsPull the card bracket back Close the card trayWhen using magnetic cards Loading cards When using contact IC cardsFor JIS II cards For ISO cardsSwitching the card thickness Remove the card thickness switching plateMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurning off the power About the Reset buttonTurn off the printer’s power Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Cleaning mode Press Enter to resetExit user mode Clearing the free counterInk mode setting Retransfer mode setting Set the retransfer temperatureSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Card size setting mode Antimagnetic setting modeTransport mode Test printCleaning the cleaning rollers Care and cleaningRemove the cleaning unit Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeCleaning the card feed rollers Set a cleaning cardFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedCleaning the card feed rollers Heat rollers Once printer servicing and cleaning Have been completedApply alcohol on the magnetic head cleaning card Set the card on the card trayTroubleshooting Cleaning rollersLayout of rollers inside the printer Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmReturn the card tray to its original position Removing card jamsPush the card tray back into position on an angle Remove any jammed cards Jog lever are supplied as standardTurn the jog dial Remove the cardSpecifications Main specificationsFront view External appearance and dimensionsUnit/mm Ultra Electronics Card Systems