Ultra electronic ID Card Printer manual Retransfer mode setting, Set retransfer film

Page 32

(to the next page)

Retransfer mode setting

Change settings according to the retranfer film and card used.

> R e t r a n s f e r >

EXIT

Exit user mode

ENTER

Set retransfer film

Set film type

> > M e d i a T y p eTwo types of frame settings (1000 frames per film, 250 frames per film)

S t d ( 1 0 0 0 / r o l l ) : 0

In addition to setting the number of frames, change the

 

EXIT

MENU

 

 

 

 

setting when using special films (not yet available). To use

 

 

 

 

 

these films, the firmware of this machine needs upgrading.

 

 

 

 

 

 

 

 

Please consult your dealer.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to select the ENTER

 

 

 

 

 

 

 

 

 

 

 

 

 

Press

 

 

 

 

setting and

to save.

 

 

 

 

 

 

 

 

press (The electronic beep sounds .)

 

 

 

 

 

 

 

 

Set the retransfer temperature.

 

 

> > T e m p . L e v e l

8 gradations can be set

 

 

 

 

 

(from –5 to +2, the larger the value the higher the temperature)

 

0 ( S t a n d a r d )

 Retransfer may be not performed well depending on the

 

 

 

 

cards. Increase the temperature level step by step until the

EXIT

MENU

card can be printed clearly.

to select the

ENTER

 

 

 

Press

setting value

to save.

 

 

 

 

 

and press (The electronic beep sounds .)

 

 

* After exiting the

RESETand then ENTER to initialize.

 

 

user mode, press

 

press

 

 

If initialization is not carried out, the temperature setting will have no effect on the printer.

Set the retransfer speed:

> > S p e e d ( F r o n t )

5 gradations can be set

(from –2 to +2, the larger the value the faster the speed)

 

- 2

 Partial incompletions may occur depending on the cards

 

 

 

 

during retransfer. The performance is increased as the

EXIT

MENU

value is lowered. Specify the value mainly on the retransfer

 

 

roller temperature setting and use the speed setting for fine

 

 

adjustments.

 

Press

to select the setting ENTER

 

to save.

 

 

value and press (The electronic beep sounds .)

Set the reverse retransfer speed:

> > S p e e d ( B a c k )

5 gradations can be set

(from –2 to +2, the higher the value the faster the speed.)

 

- 2

 

 

 

 

 Double-sided printing results in a warp depending on the

EXIT

MENU

cards. Change the speed to correct it.

to select the

 

 

 

ENTER

 

Press

setting value

to save.

 

 

and press

(The electronic beep sounds .)

31

Image 32
Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not touch the power plug during electrical Storms Do not use a line voltage other than instructedDo not wet the machine with water Do not touch the machine with wet handsDo not use the machine while it has a fault Pull out the power plug before cleaning MachineHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handProduct features Checking accessoriesBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Connecting with a host computer Set the BUS switchesSet-up Set the Scsi IDConnect the IC unit with the host computer Connecting the IC unit Sold separatelyConnect the printer and IC unit Connecting the power cord Plug the power cable into the printerCompact IC unit sold separately Connect the compact IC unit to the host computerInstalling the card stacker Mount the card stacker on the printerHang the stacker claw on the stacker receptacle Discharging the cardSetting the ink ribbon Remove the ink ribbon cassettePlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackClose the printer door When the ink ribbon is wound up to the endInsert the cassette along the guide rail Setting the retransfer film Remove the retransfer film cassetteSetting the number of frames to be used When the retransfer film is wound up to the endWind the retransfer film to take up the slack Open the printer door and insert the cassetteSetting cards Open the card trayCard bracket locks when it reaches the hole Inserting cards Unit can take about 300 0.76mm-thick cardsPull the card bracket back Close the card trayWhen using magnetic cards Loading cards When using contact IC cardsFor JIS II cards For ISO cardsSwitching the card thickness Remove the card thickness switching plateMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurning off the power About the Reset buttonTurn off the printer’s power  Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Cleaning mode Press Enter to resetExit user mode Clearing the free counterInk mode setting Retransfer mode setting Set the retransfer temperatureSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Card size setting mode Antimagnetic setting modeTransport mode Test printRemove the cleaning unit Care and cleaningCleaning the cleaning rollers Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeCleaning the card feed rollers Set a cleaning cardFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedCleaning the card feed rollers Heat rollers Once printer servicing and cleaning Have been completedApply alcohol on the magnetic head cleaning card Set the card on the card trayTroubleshooting Cleaning rollersLayout of rollers inside the printer Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmPush the card tray back into position on an angle Removing card jamsReturn the card tray to its original position Remove any jammed cards Jog lever are supplied as standardTurn the jog dial Remove the cardSpecifications Main specificationsUnit/mm External appearance and dimensionsFront view Ultra Electronics Card Systems