Ultra electronic ID Card Printer manual When using magnetic cards Loading cards, For JIS II cards

Page 21

Set-up(continued)

When using magnetic cards

Loading cards

When using cards with magnetic strips, set the cards in the following manner.

For JIS II cards:

Place the card with its magnetic stripes upward and facing the card bracket.

For ISO cards:

Place the card with its magnetic stripes downward and facing the card bracket.

CAUTION

Printing on cards with magnetic strips is not guaranteed.

When using contact IC cards

When using contact IC cards, set in the following manner.

Load cards when the printer’s LCD shows the message “Ready” or “No Card,” etc. and not when printer operations have stopped due to an error. Cards can also be loaded when the power supply is not switched on. If there is a drop in the volume of remaining cards (under 20 cards with a thickness of 0.76mm), the electronic beep sounds before every feeding.

R e a d y

N o C a r d

OR

L o a d i n g

During printing, if there is a drop in the volume of remaining cards (under 20 cards with a thickness of 76mm) an electronic beep sounds.

When “Loading” is displayed on the LCD, do not open the card tray under any circumstances. The unit is currently feeding cards. If a message other than the one above is displayed, cards can be loaded even while the unit is printing. However, you are recommended to load cards when the unit is not printing.

To prevent defective printing caused by suspended printing or vibration as a result of opening and closing the card tray, load cards with care.

Place the IC card with its IC terminal inward and facing the card bracket.

20

Image 21

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not use a line voltage other than instructed Do not touch the power plug during electrical StormsDo not wet the machine with water Do not touch the machine with wet handsPull out the power plug before cleaning Machine Do not use the machine while it has a faultHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set the BUS switches Connecting with a host computerSet-up Set the Scsi IDConnecting the IC unit Sold separately Connect the printer and IC unitConnect the IC unit with the host computer Plug the power cable into the printer Connecting the power cordCompact IC unit sold separately Connect the compact IC unit to the host computerMount the card stacker on the printer Installing the card stackerHang the stacker claw on the stacker receptacle Discharging the cardRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackWhen the ink ribbon is wound up to the end Insert the cassette along the guide railClose the printer door Remove the retransfer film cassette Setting the retransfer filmWhen the retransfer film is wound up to the end Setting the number of frames to be usedWind the retransfer film to take up the slack Open the printer door and insert the cassetteOpen the card tray Setting cardsInserting cards Unit can take about 300 0.76mm-thick cards Card bracket locks when it reaches the holePull the card bracket back Close the card trayWhen using contact IC cards When using magnetic cards Loading cardsFor JIS II cards For ISO cardsRemove the card thickness switching plate Switching the card thicknessMalfunction of the printer Remove the blue securing screwNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the powerAbout the Reset button Turning off the powerTurn off the printer’s power Initialized without winding up. DefaultUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Press Enter to reset Cleaning modeExit user mode Clearing the free counterInk mode setting Set the retransfer temperature Retransfer mode settingSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Antimagnetic setting mode Card size setting modeTransport mode Test printCare and cleaning Cleaning the cleaning rollersRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideSet a cleaning card Cleaning the card feed rollersFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedOnce printer servicing and cleaning Have been completed Cleaning the card feed rollers Heat rollersApply alcohol on the magnetic head cleaning card Set the card on the card trayCleaning rollers TroubleshootingLayout of rollers inside the printer Card turnover tableMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsRemoving card jams Return the card tray to its original positionPush the card tray back into position on an angle Jog lever are supplied as standard Remove any jammed cardsTurn the jog dial Remove the cardMain specifications SpecificationsExternal appearance and dimensions Front viewUnit/mm Ultra Electronics Card Systems