Ultra electronic ID Card Printer manual Operation, Turning on the power

Page 25

Operation

Turning on the power

1. Before turning on the power, check the following:

Make sure that the printer door is completely closed.

Make sure that the card tray is completely closed. Make sure that the host computer is correctly connected.

Make sure that any peripheral equipment is correctly connected.

Make sure that the power supply outlet is correctly connected.

Only switch the unit on after checking the above points.

*When operating this unit in the stand-alone mode, or if this unit is turned ON when a connected host computer has not yet been turned ON,

the LCD panel indication may freeze with Ver. xxx/xx/xx (the xx is varying according to the firmware version.)

This occurs because the SCSI bus is locked. If this occurs, turn OFF the power and return the bit 2 on the BUS switch to on the rear of the unit to the factory settings. Then turn ON the power again. For the factory settings, refer to p. 10 of this manual or the indication on the rear panel of the unit.

3. The unit will be in the ready status approximately 4 minutes after turning on the power.

The operation display LED (READY LED) will light up.

READY	RESET	MENU

ERROR

EXITENTER

CAUTION

Do not turn the power off while the LCD panel displays ‘Boot up’ to ‘Initializing’, as this may cause malfunctions.

2. Turn the power ON.

(I represents ON and represents OFF.)

Before turning on the host computer, make sure that the LCD panel displays Preheat or Ready.

Making settings in the user modes

When the LCD panel displays Ready or Preheating,

R e a d y

P r e h e a t i n g . .

OR

MENU

press button.

For details concerning each user mode setting, see p. 26 of this manual.

4. Enter the control command from the host computer to print cards.

The operation display LED (READY LED) will flash while the unit is receiving image data from the host computer.

READY

RESET

ERROR

EXIT

MENU

ENTER

24

Image 25

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity Machine Noise For USA onlyContents Do not use a line voltage other than instructed Do not touch the power plug during electrical StormsDo not wet the machine with water Do not touch the machine with wet handsPull out the power plug before cleaning Machine Do not use the machine while it has a faultHold the body of the power plug when pulling it Out Do not touch the power plug with a wet handChecking accessories Product featuresBefore use Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set the BUS switches Connecting with a host computerSet-up Set the Scsi IDConnect the printer and IC unit Connecting the IC unit Sold separatelyConnect the IC unit with the host computer Plug the power cable into the printer Connecting the power cordCompact IC unit sold separately Connect the compact IC unit to the host computerMount the card stacker on the printer Installing the card stackerHang the stacker claw on the stacker receptacle Discharging the cardRemove the ink ribbon cassette Setting the ink ribbonPlace the cassette upright on a flat surface during set-up Wind the ribbon, taking up the slackInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Remove the retransfer film cassette Setting the retransfer filmWhen the retransfer film is wound up to the end Setting the number of frames to be usedWind the retransfer film to take up the slack Open the printer door and insert the cassetteOpen the card tray Setting cardsInserting cards Unit can take about 300 0.76mm-thick cards Card bracket locks when it reaches the holePull the card bracket back Close the card trayWhen using contact IC cards When using magnetic cards Loading cardsFor JIS II cards For ISO cards Remove the card thickness switching plate Switching the card thickness Malfunction of the printer Remove the blue securing screwNames of parts on the operation Panel LCD operation display content Operation display LED contents LCD panelOperation Turning on the powerAbout the Reset button Turning off the powerTurn off the printer’s power Initialized without winding up. DefaultUser modes User mode screen flowMain menu Submenu User mode settingsDisplay mode settings Press Enter to reset Cleaning modeExit user mode Clearing the free counterInk mode setting Set the retransfer temperature Retransfer mode settingSet retransfer film Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Antimagnetic setting mode Card size setting modeTransport mode Test printCleaning the cleaning rollers Care and cleaningRemove the cleaning unit Wipe the head indicated with horizontally Cleaning the thermal headHow to attach the sponge Cleaning the fan filter on the back sideSet a cleaning card Cleaning the card feed rollersFrom user mode select cleaning mode Turn off the power after the cleaning card is dischargedOnce printer servicing and cleaning Have been completed Cleaning the card feed rollers Heat rollersApply alcohol on the magnetic head cleaning card Set the card on the card trayCleaning rollers TroubleshootingLayout of rollers inside the printer Card turnover tableMeaning of reset → enter buttons in the list is Error code listingTroubleshooting Mending broken ink ribbon Retransfer film About printing errorsReturn the card tray to its original position Removing card jamsPush the card tray back into position on an angle Jog lever are supplied as standard Remove any jammed cardsTurn the jog dial Remove the cardMain specifications SpecificationsFront view External appearance and dimensionsUnit/mm Ultra Electronics Card Systems