Ultra electronic ID Card Printer manual Setting the bend remedy mode

Page 34

(to the next page)

Setting the bend remedy mode

Single-sided printing may cause a bend depending on the cards. Adjust the setting to get rid of the bend.

> B e n d R e m e d y >	EXIT	Exit user
		Exit user
		mode

ENTER

CAUTION

When printing on both sides is done with “Remedy roller temperature setting” set to a high temperature, the cards may show a large deformation.

Please set this item to OFF for printing on both sides.

Set the bend remedy roller temperature

> > T e m p L e v e l

There are 9 bend remedy roller temperature settings:

(off and from –5 to +2 the larger the value the higher the temperature).

	o f f
EXIT	MENU		ENTER
	Press	to select the setting and press		to save.
		(The electronic beep sounds.)
		RESET		ENTER
	* After exiting the user mode, press		and then press
		to initialize.
		If initialization is not carried out, the temperature setting will have no
		effect on the printer.

Bend remedy speed settings

> > S p e e d

5 gradations can be set

	(from –2 to +2, the larger the value the faster the speed.)
	- 2
EXIT	MENU	ENTER	to save.
	Press	to select the setting value and press	to save.
		(The electronic beep sounds.)

> > C o o l i n g T i m e			Cooling time setting:
	- 2		16 gradations can be set (none and 1-15, unit: seconds).

EXIT	MENU	ENTER	to save.
	Press	to select the setting value and press	to save.
		(The electronic beep sounds.)

				Memo
	CAUTION			Memo
		If the bend remedy temperature
			1. Setting temperature and speed of the bend


	setting is set to off from any other setting, the			remedial roller
	preheating status will remain the same until the roller			Adjust the “roller temperature” setting in principle
	temperature falls (for approximately 10 minutes).			to correct the bend of the card, and use the
	This is not a malfunction. Leave the unit in ready			“correction speed” setting for fine adjustments.
	status and wait.		2. Setting waiting time for cooling the card
				This provides the time for a special film, which
				will be marketed in the future, to cool down to
				prevent the card and retransfer film from sticking
				together after printing.

33

Image 34

Contents ID Card Printer Magicard Prima Re-transfer Laminating Printer Declaration of Conformity For USA only Machine NoiseContents Do not wet the machine with water Do not touch the power plug during electrical StormsDo not use a line voltage other than instructed Do not touch the machine with wet handsHold the body of the power plug when pulling it Out Do not use the machine while it has a faultPull out the power plug before cleaning Machine Do not touch the power plug with a wet handBefore use Product featuresChecking accessories Handling of transfer film Ink ribbons and cardsInstallation Names of parts Set-up Connecting with a host computerSet the BUS switches Set the Scsi IDConnect the printer and IC unit Connecting the IC unit Sold separatelyConnect the IC unit with the host computer Compact IC unit sold separately Connecting the power cordPlug the power cable into the printer Connect the compact IC unit to the host computerHang the stacker claw on the stacker receptacle Installing the card stackerMount the card stacker on the printer Discharging the cardPlace the cassette upright on a flat surface during set-up Setting the ink ribbonRemove the ink ribbon cassette Wind the ribbon, taking up the slackInsert the cassette along the guide rail When the ink ribbon is wound up to the endClose the printer door Setting the retransfer film Remove the retransfer film cassetteWind the retransfer film to take up the slack Setting the number of frames to be usedWhen the retransfer film is wound up to the end Open the printer door and insert the cassetteSetting cards Open the card trayPull the card bracket back Card bracket locks when it reaches the holeInserting cards Unit can take about 300 0.76mm-thick cards Close the card trayFor JIS II cards When using magnetic cards Loading cardsWhen using contact IC cards For ISO cardsMalfunction of the printer Switching the card thicknessRemove the card thickness switching plate Remove the blue securing screwNames of parts on the operation Panel Operation display LED contents LCD panel LCD operation display contentTurning on the power OperationTurn off the printer’s power Turning off the powerAbout the Reset button Initialized without winding up. DefaultUser mode screen flow User modesUser mode settings Main menu SubmenuDisplay mode settings Exit user mode Cleaning modePress Enter to reset Clearing the free counterInk mode setting Set retransfer film Retransfer mode settingSet the retransfer temperature Set the retransfer speedBuzzer mode setting Setting the bend remedy mode Transport mode Card size setting modeAntimagnetic setting mode Test printCleaning the cleaning rollers Care and cleaningRemove the cleaning unit Cleaning the thermal head Wipe the head indicated with horizontallyCleaning the fan filter on the back side How to attach the spongeFrom user mode select cleaning mode Cleaning the card feed rollersSet a cleaning card Turn off the power after the cleaning card is dischargedApply alcohol on the magnetic head cleaning card Cleaning the card feed rollers Heat rollersOnce printer servicing and cleaning Have been completed Set the card on the card trayLayout of rollers inside the printer TroubleshootingCleaning rollers Card turnover tableError code listing Meaning of reset → enter buttons in the list isTroubleshooting About printing errors Mending broken ink ribbon Retransfer filmReturn the card tray to its original position Removing card jamsPush the card tray back into position on an angle Turn the jog dial Remove any jammed cardsJog lever are supplied as standard Remove the cardSpecifications Main specificationsFront view External appearance and dimensionsUnit/mm Ultra Electronics Card Systems