A&D MC-10K, MC-30K Initializing the Balance, Step Press Key, To cancel This operation, press Key

Page 28

9-2. Initializing the Balance

This function returns the following parameters to factory settings.

Calibration data

Function table

The sample unit mass value (counting mode), 100% reference mass value (percent mode)

The data that is stored in the balance using the data memory function

External calibration weight and target weight value Function switch settings

Note Be sure to calibrate the balance after initialization.

Step 1 Press the ON:OFF key to turn off the display.

Step 2 While pressing and holding the PRINT key and the SAMPLE key, press the ON:OFF key to display p5 .

Step

3

Press the

 

 

 

 

 

key to display

 

 

 

.

 

 

SAMPLE

 

Clr

Step

4

Press the

 

 

 

 

key.

 

 

 

 

 

 

PRINT

 

 

 

 

 

 

 

 

To cancel

this operation, press the

 

 

 

key.

 

 

 

CAL

Step

5

Press the

 

 

 

 

 

key to display

 

 

.

 

RE-ZERO

 

 

Clr go

Step

6

Press the

 

 

 

 

key to initialize the balance.

 

PRINT

 

The balance will automatically return to the weighing mode.

With these keys Press the key held down

p5

Clr

Clr no

Clr go

end

0 .000 g

26

Page 27 Page 29
Image 28
Page 27 Page 29
Contents
MC-10K MC-30K 1WMPD4002203AThis Manual and Marks All rights reservedContents 10-6 10-514-1-1 Averaging Range f1-b and Averaging Time f1-t 14-1-2 Introduction FeaturesAbout This Manual Compliance Compliance with the following Council DirectivesUnpacking And Installing The Balance To keep waterproof DustproofAuto-centering Pan AX-MC10K/30KPAN Installation Procedure Installing the Balance EarthPrecautions Before UseDuring Use After UsePower Supply Display Symbols And Key Operation Key When pressed and released When pressed and heldKey Operations DisplayWeighing Units Tael HK general, Singapore Selecting a Weighing Unit Mode WeighingBasic Weighing F1l Filter Used DisplayWhen Building into a System Weighing Speed Adjustment Balance during adjustment Self Check Function with Response AdjustmentDo not allow vibration or drafts to affect Calibration Group CalibrationTerms Automatic Self Calibration Automatic self calibration due to changes in temperature150 g ~ +0.159 g One-Touch Calibration Calibration using the internal massAbout the internal mass Calibration Using an External Weight When the MC-10K is used Calibration Test Using an External Weight Print key...... To store the new weight value. Even if Remove Remove the weight from the pan Step Balance displays Step Confirm that there is nothing on the pan and pressCorrecting the Internal Mass Value Key Function Switch And Initialization Permit or InhibitTo cancel This operation, press Key Initializing the BalanceStep Press Key Step Press Key to displayCheck the settings and condition before changing parameters Function TableStructure and Sequence of the Function Table Display and Operation KeysDetails of the Function Table Data output mode Cp fnc Cp-bBep LO buzzerTimeout AK, Error codeTime/Date output Dout ID number outputID number setting Internal mass correctionF1-b Averaging range for First moving Average F1-tZero upon power-on p-tr Description of the Class Environment, DisplayCondition Cond Stability band width 5t-bDescription of the Item Data Output Mode Key modeStream mode Auto print modes a and BInterval memory mode Description of the Item Data FormatStandard format 5if type DP Dump print format 5if typeKF format MT formatNU numerical format 5if type CSV formatData number DateTime Tare valueNegative error Data Format ExamplesStable OverloadID Number And GLP Report Setting the ID NumberDisplay character set Calibration report using the internal mass GLP ReportSpace, Ascii 20h Terminator, CR , LF or CRCalibration test report using an external weight Calibration report using an external weightSignature Space, Ascii 20h Operation Title block and end blockEnd block Standard Input And Output Interface RS-232C and External Contact InputSub 25 pin numbers Sub 25 pin assignmentsExternal contact input RS-232C TerminalsOption Settings Not Auto print polarityNecessary Data output pauseUsing Windows Communication Tools Software WinCT Using the WinCT software, the balance can do the followingRsCom RsKeyCommands Command ListAcknowledge Code and Error Codes Control Using CTS and RTS Settings Related to RS-232CCommand Personal computer Time Balance Command Weighing modeExtended Function Page Page Maintenance Treatment of the BalanceTroubleshooting Checking the Balance Performance and EnvironmentChecking that the balance performs properly Weighing method16-2 Automatic response adjustment zero error Automatic response adjustment unstable errorInternal error Clock battery errorOther Display Asking for RepairSpecifications External Dimensions Unit mmAD-8922A Remote controller Options and Peripheral InstrumentsAX-MC10K/30KPAN Auto-centering Pan AD-8121B PrinterRechargeable Battery Foot SwitchWeighing Environment Logger Data LoggerTerms/Index TermsMemory function Nothing is on the weighing panKeys and symbols IndexError Mode MT formatF1l FUlPage UK Office German Sales OfficeKorea Limited Instruments India Private Limited
Top Page Image Contents