American Power Conversion MX28B200 user manual Remote Monitoring

Page 4

4	OPERATION		23
	4.1.	TECHNICAL DESCRIPTION	23
	4.2.	RECTIFIER MANAGEMENT	23
	AC Input Power		23
	DC Output Power		23
	Rectifier alarms reporting		23
	4.3.	SYSTEM MANAGEMENT	24
	System Output Capacity		24
	System Voltage Control		24
	System Current		24
	System Status and Alarm Reporting		25
	4.4.	DC DISTRIBUTION	25
	4.5.	BATTERY MANAGEMENT	25
	Battery Charging and Protection		25
	Battery Temperature Compensation		26
	Battery/Load Low Voltage Disconnect		26
	4.6.	CONTROLS AND INDICATORS	26
	Front Panel User Interface		26
	Parameter Locations, Descriptions, and Default Values		28
	Control Unit Menu Structure		37
	Front Panel LED Indicators		42
	4.7. ALARM OUTPUTS (OUTPUT RELAYS)		43
	4.8. EXTERNAL ALARM INPUTS (INPUT RELAYS)		43
5	REMOTE MONITORING		45
	5.1.	DESCRIPTION	45
	5.2.	PHYSICAL CONNECTIONS	45
	5.3.	COMMAND AND MONITORING PROTOCOL	45
6	SPECIFICATIONS		47
	6.1.	AC INPUT	47
	1MRF28H54BV Rectifiers		47
	1MRF28H54BV50 Rectifiers		47

6.2.DC OUTPUT (WITH EITHER 1MRF28H54BV RECTIFIERS AND 1MRF28H54BV50

RECTIFIERS)		47
6.3.	CONTROLS AND INDICATORS	48
Rectifiers		48
6.4.	CONTROLS AND INDICATORS	49
Power Shelf Control Unit		49
6.5.	MECHANICAL	49
6.6.	ENVIRONMENTAL	51
6.7.	COMPLIANCE	51
7 APC WORLDWIDE CUSTOMER SUPPORT		53
8 WARRANTY		55

Page iv

MX28B200/400 –48 VDC User’s Manual (990-9133)

Image 4

Contents VDC Power Systems Page Table of Contents Remote Monitoring Revision History Revision Date DescriptionPage Safety First General PrecautionsPage Introduction General Information2 MX28B Block Diagram How to Use This Manual Page Installation Mechanical InstallationUnpacking Equipment Room / LocationAC Power Connections VentilationPlanning the Battery installation Battery ConnectionsConnecting the Cables Battery Temperature Probe Installation DC System GroundingDC Power Output Over-Current Protection DC Circuit Breakers#10 studs on 5/8 centers DC GMT Fuses Fuse Rating Part NumberInstallation of Circuit Breakers and Fuses Plug-in Circuit Breaker InstallationGMT Fuse Installation Load ConnectionsCable Size Considerations Circuit Breaker Connections 1 to 50 AmpsCircuit Breaker Connections 60-100 Amps 1 Standard lug for 1 to 50A breakersGMT Fuse Connections 2 Adaptor and lugs for 60-100 Amp breakersRJ45 Ethernet Connector Monitoring and Relay Output ConnectionsFront Panel DB9 Connection Smart Cable DB9 ConnectionExternal Alarm Input Connections NO-NC-CRectifier Module Installation Initial Power-Up and CheckoutSystem Parameters Verification/Adjustment Full System Power Up Technical Description OperationRectifier Management System Management System Output CapacitySystem Voltage Control System CurrentBattery Management System Status and Alarm ReportingBattery Charging and Protection DC DistributionControls and Indicators Battery Temperature CompensationBattery/Load Low Voltage Disconnect Front Panel User InterfaceMX28B Status Alarms System Modules Batt PIN OEM Parameter Locations, Descriptions, and Default Values Batt Disc Alm m+ MinorBatt Disc Thr m+ 10 aCir Bkr 48VCir Bkr 1 Alm m+ MajorFW Version 000189GMT 1 Alm GMT 8 AlmEnable LVD ResetIn-Rly 1 Alm IgnoreOEM S Offset Out-Rly 1 Alm m+Out-Rly 6 Alm m+ Out-RlyRectFailComm MinRect Cfg Alm Rect CL AlmDisable Rect 1 FFRect 1 RFA Rect RFA AlmSys LT Thr Sys LV AlmSys LV Thr 50.00SYS MS System Module SET-ALM Setup DA Control Unit Menu StructureV e l C o n d L e v e l I r d L e v e l U r t h L e v e l SYS Sysin AM Info Modgmt LM Alias GMT MOD Modlvd Front Panel LED Indicators Alarm Outputs Output Relays External Alarm Inputs Input RelaysPage Command and Monitoring Protocol Remote MonitoringDescription Physical ConnectionsPage Specifications AC Input1MRF28H54BV Rectifiers 1MRF28H54BV50 RectifiersRectifiers PscuPower Shelf Control Unit MechanicalMounting Environmental CompliancePage APC Worldwide Customer Support Page Warranty General Provisions