American Power Conversion SYMSTRF3I user manual Environmental Requirements, Heat Output

Page 17

Environmental Requirements

Install SymmetraTM in a temperature controlled, clean, dry, and protected indoor area that is free of conductive contaminants. The environment must have adequate airflow, and be free of corrosive fumes.

Environmental Condition

Acceptable Range

 

 

Temperature

32°F - 104°F (0°C - 40°C)

 

 

Relative Humidity

0 - 95% non-condensing

 

 

Elevation

0 to 10,000 feet above mean sea level (0 to 3,048 m)

 

 

Heat Output

Heat output of the SymmetraTM is significantly increased when batteries are charging. Battery recharge periods are relatively infrequent.

SymmetraTM Component

BTU Output

BTU Output

(Batteries Charged)

(Batteries Charging)

 

 

 

 

 

 

 

SYMINIF

3,413

8,670

North

 

SYMINIF-PD

 

 

American

 

 

 

SYMSTRF

 

 

Models

6,826

15,640

 

 

SYMSTRF-PD

 

 

 

 

 

 

 

International

SYMINIFI

2,321

7,578

 

 

 

1:1 Models

SYMSTRFI

 

 

 

4,642

13,456

 

 

3:1 Model

SYMSTRF3I

 

 

 

 

 

 

Short-Term Battery Module Storage Requirements

Battery modules must be temporarily stored until the electrical wiring is connected and the SymmetraTM is ready to be powered.

νBatteries should be stored at 0°F to 77°F (-18°C to 25°C) to preserve battery life.

νStorage environment can be within 0 to 100% relative humidity , non-condensing.Note: Condensation will cause corrosion of electronic and chassis parts.

Caution!

νInstalling battery modules in a SymmetraTM that is not powered will discharge the batteries and could damage them permanently. Do not install battery modules into the SymmetraTM frame until after the electrical wiring connections have been made, and the system is ready to be powered.

990-7164-001

Site Requirements - Page 3

 

Image 17
Contents 380V/400V/415V 31 Frame Model SYMSTRF3I Life Support Policy Limited WarrantyTable of Contents Page Safety Symbols Safety InformationRadio Frequency Interference Operation SymbolsFrame Model Description Illustration WelcomeModels System Components SymmetraTM Component Description Model Specific Details SYMSTRF3I SYMSTRF3I SymmetraTM Components Description Specific To ModelBasic Operation Glossary of SymmetraTM Terms 8 Introduction Operating Space Requirements Site RequirementsRear Clearance Front ClearanceModels Structural RequirementsHeat Output Short-Term Battery Module Storage RequirementsEnvironmental Requirements VAC Electrical Requirements Input/OutputEPO Specifications Electrical Requirements EPO SwitchElectrical Wiring Overview Receiving and Unpacking SymmetraTM Component Shipping Weight Shipping DimensionsReceiving the SymmetraTM Inspect PackagingMoving The SymmetraTM Frame and Modules Unpacking the SymmetraTM Frame 4 Receiving and Unpacking Model SYMSTRF3I Electrical InstallationElectrical Requirements EPO Switch Wiring RequiredElectrical Wiring Overview Input/Output Wiring Minimum Input/Output Wiring ProcedureWire Size Emergency Power Off Switch Wiring Required Emergency Power Off Switch Wiring Procedure Bypass Balancing Transformer Wiring Optional Wiring Symbol Description Minimum Wire Gauge Bypass Balance Transformer Wiring Procedure OptionalWiring Verification Procedure Reported Output Voltage OutVHz APC Worldwide Technical Support Telephone Numbers Securing The Frame Setting The Leveling Feet Startup ProcedurePower Module Installation Battery Module Installation System Startup Procedure Configuration Configuration and Advanced OperationDisplay Settings System Settings SetupAdvanced Operation PowerView Interface PowerView Component Description PowerView ComponentsLanguage Chip Replacement Procedure Language ConfigurationTop-Level Menu Screen Startup ScreenStatus ControlSetup PowerView CommandsLogging AccessoriesFunction Options DisplayHelp DiagnosticsWall Mounting the PowerView PowerView Meaning Corrective Action Message Start-Up TroubleshootingPowerView Meaning Corrective Action Message General Alarm PowerView Meaning Corrective Action Message ModuleFailure ThresholdFault PowerView Meaning Corrective Action Message BypassGeneral PowerView Meaning Corrective Action Message6 Troubleshooting Appendix B Module Failure Alarm Indicators Module ReplacementReturning Modules to APC Technical Support & Obtaining Replacement ModuleReplacement Battery Module Verification Battery Module ReplacementReplacement Module Verification Power Module ReplacementReplacement MIM Verification Main Intelligence Module ReplacementRedundant Intelligence Module Replacement Replacement RIM Verification6 Module Replacement Appendix C Operation SpecificationsInput Specifications Compliance Specifications Output SpecificationsPhysical Specifications Page Tel0800 180