American Power Conversion SYMSTRF3I user manual Startup Screen, Top-Level Menu Screen

Page 46

The Startup Screen

The factory default startup screen is opened by pressing the escape key. It displays the following information:

νFuel Percentage - the percentage of battery capacity (fuel) that is presently available.

νLoad Percentage - the percentage of system capacity that is being used to supply conditioned power to the load equipment.

νVoltage and Frequency - the input/output voltage, and the ouput frequency.

νRun Time - the run time that can be expected, based on the amount of power required by the load equipment, and the power capacity of all battery modules connected to the SymmetraTM Power Array.

Note: The PowerView interface will “time out” after ten minutes of inactivity, and the LCD display will go blank. The screen display will reappear when any key is touched.

Note: The startup screen for the international single phase models is depicted. Your startup screen may vary.

Top-Level Menu Screen

Press the escape key to open the “Top-Level Menu” screen. This screen is the “launching pad” to monitor, com- mand and configure the system. Refer to the following tables for all PowerView commands and controls. Note: The selection arrow in the illustration below is used to select a command. Pressing the up or down key moves the selection arrow to the desired command, and then pressing the enter key opens it.

Page 4 - The PowerView Interface - Appendix A	990-7169-001

Image 46

Contents 380V/400V/415V 31 Frame Model SYMSTRF3I Limited Warranty Life Support PolicyTable of Contents Page Safety Information Safety SymbolsOperation Symbols Radio Frequency InterferenceModels WelcomeFrame Model Description Illustration System Components SymmetraTM Component Description Model Specific Details SYMSTRF3I SymmetraTM Components Description Specific To Model SYMSTRF3IBasic Operation Glossary of SymmetraTM Terms 8 Introduction Rear Clearance Site RequirementsOperating Space Requirements Front ClearanceStructural Requirements ModelsEnvironmental Requirements Short-Term Battery Module Storage RequirementsHeat Output Electrical Requirements Input/Output VACElectrical Requirements EPO Switch EPO SpecificationsElectrical Wiring Overview Receiving the SymmetraTM SymmetraTM Component Shipping Weight Shipping DimensionsReceiving and Unpacking Inspect PackagingMoving The SymmetraTM Frame and Modules Unpacking the SymmetraTM Frame 4 Receiving and Unpacking Electrical Installation Model SYMSTRF3IEPO Switch Wiring Required Electrical RequirementsElectrical Wiring Overview Input/Output Wiring Wire Size Input/Output Wiring ProcedureMinimum Emergency Power Off Switch Wiring Required Emergency Power Off Switch Wiring Procedure Bypass Balancing Transformer Wiring Optional Bypass Balance Transformer Wiring Procedure Optional Wiring Symbol Description Minimum Wire GaugeWiring Verification Procedure Reported Output Voltage OutVHz APC Worldwide Technical Support Telephone Numbers Startup Procedure Securing The Frame Setting The Leveling FeetPower Module Installation Battery Module Installation System Startup Procedure Display Settings Configuration and Advanced OperationConfiguration System Settings SetupAdvanced Operation PowerView Interface PowerView Components PowerView Component DescriptionLanguage Configuration Language Chip Replacement ProcedureStartup Screen Top-Level Menu ScreenControl StatusPowerView Commands SetupAccessories LoggingDisplay Function OptionsDiagnostics HelpWall Mounting the PowerView Troubleshooting PowerView Meaning Corrective Action Message Start-UpPowerView Meaning Corrective Action Message General Failure PowerView Meaning Corrective Action Message ModuleAlarm ThresholdPowerView Meaning Corrective Action Message Bypass FaultPowerView Meaning Corrective Action Message General6 Troubleshooting Appendix B Module Replacement Module Failure Alarm IndicatorsTechnical Support & Obtaining Replacement Module Returning Modules to APCBattery Module Replacement Replacement Battery Module VerificationPower Module Replacement Replacement Module VerificationRedundant Intelligence Module Replacement Main Intelligence Module ReplacementReplacement MIM Verification Replacement RIM Verification6 Module Replacement Appendix C Input Specifications SpecificationsOperation Physical Specifications Output SpecificationsCompliance Specifications Page Tel0800 180