Toshiba E6581830 instruction manual 120

E658130

■Input function selection from the CC-Link.

The function numbers selection of the RYn2 to RYn8 function valid from the command of the CC-Link are following

boldface numbers.
Positive logic	Negative logic	Function	Speed control	PM control	V/f
0	1	No function is assigned	●/●	●	●
2	3	Forward run command	●/●	●	●
4	5	Reverse run command	●/●	●	●
6	7	Standby	●/●	●	●
8	9	Reset command	●/●	●	●
10	11	Preset speed command 1	●/●	●	●
12	13	Preset speed command 2	●/●	●	●
14	15	Preset speed command 3	●/●	●	●
16	17	Preset speed command 4	●/●	●	●
18	19	Jog run mode	●/●	●	●
20	21	Emergency stop by external signal *	●/●	●	●
22	23	DC braking command	●/●	●	●
24	25	2nd acceleration/deceleration	●/●	●	●
26	27	3rd acceleration/deceleration	●/●	●	●
28	29	2nd V/F control mode switching	●/●	●	●
32	33	2nd stall prevention level	●/●	●	●
36	37	PID control prohibition	●/●	●	●
46	47	External thermal error input	●/●	●	●
48	49	Forced local from communication	●/●	●	●
50	51	Operation hold (hold of 3-wire operation)	●/●	●	●
52	53	PID integral/differential clear	●/●	●	●
54	55	PID characteristics switching	●/●	●	●
56	57	Forced run operation	●/●	●	●
58	59	Fire speed operation	●/●	●	●
60	61	Acceleration/deceleration suspend signal	●/●	●	●
62	63	Power failure synchronized signal	●/●	●	●
64	65	My function-S trigger signal	●/●	●	●
74	75	Integrating wattmeter(kWh) display clear	●/●	●	●
76	77	Trace back trigger signal	●/●	●	●
78	79	Light-load high-speed operation	●/●	●	●
		prohibitive signal
80	81	Holding of RY-RC terminal output	●/●	●	●
82	83	Holding of OUT terminal output	●/●	●	●
88	89	Frequency UP	●/●	●	●
90	91	Frequency DOWN	●/●	●	●
92	93	Clear frequency UP/DOWN	●/●	●	●
96	97	Coast stop command	●/●	●	●
98	99	Forward/reverse selection	●/●	●	●
100	101	Run/Stop command	●/●	●	●
104	105	Frequency setting mode forced switching	●/●	●	●
106	107	Frequency setting mode terminal block	●/●	●	●
108	109	Command mode terminal block	●/●	●	●
110	111	Parameter editing permission	●/●	●	●
120	121	Fast stop command 1	●/●	●	●
122	123	Fast stop command 2	●/●	●	●
134	135	Traverse permission signal	●/●	●	●
136	137	Low voltage operation signal	●/●	●	●
140	141	Forward deceleration	●/●	●	●
142	143	Forward stop	●/●	●	●
144	145	Reverse deceleration	●/●	●	●
146	147	Reverse stop	●/●	●	●
152	153	No.2 motor switching	●/●	●	●
		(AD2 + VF2 + OCS2)
200	201	Parameter editing prohibition	●/●	●	●
202	203	Parameter reading prohibition	●/●	●	●

* This function is not dependent on cmod.

- 22 -