Toshiba E6581830 instruction manual Programming examples

Page 36

E658130

6.Programming examples

This chapter provides programming examples which control the inverter with the PLC.

Item

Programming Example

Refer to Page

6.1

Reading the inverter status

Reading the inverter status from the buffer

- 38 -

memory of the master station.

6.2

Setting the command mode

Command mode from CC-Link is confirmed.

- 39 -

6.3

Setting the operation commands

Commanding the forward rotation.

- 40 -

6.4

Setting the reference frequency

Setting to 50.00Hz.

- 40 -

6.5

Setting the monitoring function

Monitoring the output frequency.

- 41 -

6.6

Writing a parameter value

Setting the f311 [Reverse-run prohibition

- 42 -

selection] to [1 : Prohibit reverse run].

6.7

Reading a parameter value

Reading the parameter f311.

- 42 -

6.8

Reading the the fault record

Reading the fault record

- 44 -

6.9

Inverter reset

Resetting the inverter.

- 45 -

System configuration for programming example

Master unit

Station 1

Station 2

Inverter

Inverter

PS

Q02

QJ61

Input

Output

Unit

CPU

BT11N

Unit

Unit

(X/Y00

(X20

(Y30

to 1F)

to X2F)

to 3F)

X0020

Y30

CC-Link communication cable

The example of CC-Link communication network composition

･CPU	Mitsubishi Electric Corp.	Q02CPU
･Master unit	Mitsubishi Electric Corp.	QJ61BT11N
･Input module	Mitsubishi Electric Corp.	QX40
･Output module	Mitsubishi Electric Corp.	QY40P
･CC-Link dedicated cable	Kuramo Electric Corp.	FANC-110SBH
･Inveter	Toshiba	TOSVERT VF-S15(2 uints)
		One station is occupied
･CC-Link option	Toshiba	CCL003Z(2 units)

- 35 -

Image 36

Contents CCL003Z Introduction Handling in general Table of Contents Basic specifications OverviewCC-Link Version CC-Link VerNames and functions OutlineSLD Installation on inverter Connection cableTerminating resistor Connection of CC-Link master unit and inverter DA,DBMaximum connection number of units Page LED indicator RUN ERRRUN Initial setting FunctionsCommunication parameters for CCL003Z C101CC-Link function setting Station number setting Baud rate settingCC-Link extended setting Run and frequency operation command Basic functionsMonitor Writing and reading the parameterI/O signal list One station is occupied CC-Link Ver.1 c122=0 RAMDouble setting is selected CC-Link Ver.2 c122=1 Quadruple setting is selected CC-Link Ver.2 c122=2Octuple setting is selected CC-Link Ver.2 c122=3 Trip history Detail of input and output signals RYnF Instruction code execution request120 OFF ST = on On ST = OFFRemote Register Assignment Instruction code 3 It is the same as instruction code 1 Monitor code RWwn is set Signal Description Instruction Codes 00EDH00FCH 00FDHEx A900 A900H, C123 C123H Details of an error code Fault record display example Description of reply code Reply codeDescription of monitor code Description of input terminal information Description of output terminal informationProgramming examples SB0 SW0RWr0 Program example for reading the inverter status X0FEND Program example for setting the operation mode Program example for setting the operation commands Program example for setting the running frequencyPLS SETProgram example for monitoring the output frequency Program example for parameter writing Program example for parameter reading Program example for trip information reading MOVProgram example for resetting the inverter at inverter error Instructions Option error Disconnection error of network cableUnusual diagnosis How to check the error using the LEDs CPUCCL003Z Time Line ERR RUNTime Line RUNTime RUN ERR Line RUNERR Time RUN Time ERR