|
|
|
| E658130 |
|
| |||
Table of Contents |
| |||
1. | OVERVIEW | - 4 - | ||
2. | BASIC SPECIFICATIONS | - 4 - | ||
| 2.1. | - 5 - | ||
| 2.1.1. | - 5 - | ||
| 2.1.2. | - 5 - | ||
3. | NAMES AND FUNCTIONS | - 6 - | ||
| 3.1. | Outline | - 6 - | |
4. | INSTALLATION ON INVERTER | - 7 - | ||
| 4.1. | Connection cable | - 7 - | |
| 4.2. | Terminating resistor | - 7 - | |
| 4.3. Connection of | - 8 - | ||
| 4.4. The maximum connection number of units | - 9 - | ||
| 4.5. | LED indicator | - 11 - | |
5. | FUNCTIONS | - 12 - | ||
| 5.1. | Initial setting | - 12 - | |
| 5.2. Communication parameters for CCL003Z | - 13 - | ||
| 5.3. | - 14 - | ||
| 5.3.1. | Station number setting | - 14 - | |
| 5.3.2. | Baud rate setting | - 14 - | |
| 5.3.3. | - 15 - | ||
| 5.4. | Basic functions | - 16 - | |
| 5.4.1. Run and frequency operation command | - 16 - | ||
| 5.4.2. | Monitor | - 16 - | |
| 5.4.3. Writing and reading the parameter | - 16 - | ||
| 5.5. | I/O signal list | - 17 - | |
| 5.5.1. One station is occupied | - 17 - | ||
| 5.5.2. Double setting is selected | - 18 - | ||
| 5.5.3. Quadruple setting is selected | - 18 - | ||
| 5.5.4. Octuple setting is selected | - 19 - | ||
| 5.5.5. | Faults history | - 20 - | |
| 5.5.6. Detail of input and output signals | - 21 - | ||
| 5.5.7. | Remote Register Assignment | - 24 - | |
| 5.5.8. | Instruction Codes | - 28 - | |
| 5.5.9. The details of an error code | - 30 - | ||
| 5.5.10. | Description of reply code | - 32 - | |
| 5.5.11. | Description of monitor code | - 33 - | |
| 5.5.12. | Description of input terminal information | - 34 - | |
| 5.5.13. | Description of output terminal information | - 34 - | |
6. | PROGRAMMING EXAMPLES | - 35 - | ||
| 6.1. Program example for reading the inverter status | - 38 - | ||
| 6.2. Program example for setting the operation mode | - 39 - | ||
| 6.3. Program example for setting the operation commands | - 40 - | ||
| 6.4. Program example for setting the running frequency | - 40 - | ||
| 6.5. Program example for monitoring the output frequency | - 41 - | ||
| 6.6. Program example for parameter writing | - 42 - | ||
| 6.7. Program example for parameter reading | - 43 - | ||
| 6.8. Program example for fault record reading | - 44 - | ||
| 6.9. Program example for resetting the inverter at inverter error | - 45 - | ||
| 6.10. | Instructions | - 46 - | |
7. | UNUSUAL DIAGNOSIS | - 47 - | ||
| 7.1. | Option error | - 47 - | |
| 7.2. Disconnection error of network cable | - 47 - | ||
| 7.3. How to check the error using the LEDs | - 48 - | ||
- 3 -