E658130
5.5.2. Double setting is selected (CC-Link Ver.2) (c122=1)
This option occupies one station area of the buffer memory of the PLC.
In the case of c122 = 1, there are remote I/O (RX, RY both 32 bits(same as
* Default value of RY and RX is 0.
Remote register (Default value = 0)
RWr | Inverter → PLC | RWw | PLC → Inverter |
Address | Signal | Address | Signal |
RWr n | Monitor value 1 | RWw n | Monitor code (1 and 2) |
RWr n+1 | Monitor value 2 | RWw n+1 | Set frequency |
(output frequency) |
|
| |
|
|
| |
RWr n+2 | Reply code | RWw n+2 | Instruction code |
RWr n+3 | Read data | RWw n+3 | Write data |
RWr n+4 | Monitor value 3 | RWw n+4 | Monitor code 3 |
RWr n+5 | Monitor value 4 | RWw n+5 | Monitor code 4 |
RWr n+6 | Monitor value 5 | RWw n+6 | Monitor code 5 |
RWr n+7 | Monitor value 6 | RWw n+7 | Monitor code 6 |
"n" is depend on the station number.
5.5.3. Quadruple setting is selected (CC-Link Ver.2) (c122=2)
This option occupies one station area of the buffer memory of the PLC.
In the case of c122 = 2, there are remote I/O (RX, RY both 32 bits(same as
* Default value of RY and RX is 0.
Remote register (Default value = 0)
RWr | Inverter → PLC | RWw | PLC → Inverter | |||
Address |
| Signal | Address |
| Signal | |
RWr n | Monitor value 1 | RWw n | Monitor code (1 and 2) | |||
RWr n+1 | Monitor value 2 | RWw n+1 | Set frequency |
| ||
(output frequency) |
|
|
|
| ||
|
|
|
|
| ||
RWr n+2 | Reply code |
| RWw n+2 | Instruction code | ||
RWr n+3 | Read data |
| RWw n+3 | Write data |
| |
RWr n+4 | Monitor value 3 | RWw n+4 | Monitor code 3 |
| ||
RWr n+５ | Monitor value 4 | RWw n+5 | Monitor code 4 |
| ||
RWr n+６ | Monitor value 5 | RWw n+6 | Monitor code 5 |
| ||
RWr n+７ | Monitor value 6 | RWw n+7 | Monitor code 6 |
| ||
| Upper 8 | Trip history No. |
| Upper 8 |
| Trip history No. |
| Bits |
| Bits |
| ||
RWr n+8 |
| RWw n+8 |
|
| ||
Lower 8 | Trip code | Lower 8 |
| Reserved** | ||
|
|
| ||||
| Bits |
| Bits |
| ||
|
|
|
|
| ||
RWr n+9 | Trip information (output frequency) | RWw n+9 | Reserved** |
| ||
RWr n+A | Trip information (output current) | RWw n+A | Reserved** |
| ||
RWr n+B | Trip information (output voltage) | RWw n+B | Reserved** |
| ||
RWr n+C | Trip information (energization time) | RWw n+C | Reserved** |
| ||
RWr n+D | Reserved* |
| RWw n+D | Reserved** |
| |
RWr n+E | Reserved* |
| RWw n+E | Reserved** |
| |
RWr n+F | Reserved* |
| RWw n+F | Reserved** |
| |
"n" is depend on the station number.
*The bit described " Reserved " is unstable. Don't use the “Reserved " bit for the judgment.
**Do not use it.
-18 -