Xilinx SP605 manual Oscillator Socket Single-Ended, 2.5V or

Page 24

Chapter 1: SP605 Evaluation Board

Oscillator Socket (Single-Ended, 2.5V or 3.3V)

One populated single-ended clock socket (X2) is provided for user applications. The option of 2.5V or 3.3V power may be selected via a 0 ohm resistor selection. The SP605 board is shipped with a 27 MHz 2.5V oscillator installed.

Figure 1-8shows the unpopulated user oscillator socket. This figure indicates the socket pin 1 location. Figure 1-9shows the oscillator installed, with its pin 1 location identifiers.

Silkscreened outline has beveled corner

Socket has notch in crossbar

UG526_08_100509

Figure 1-8:SP605 X2 Oscillator Socket Pin 1 Location Identifiers

Oscillator top has corner dot marking

Oscillator body has one square corner

UG526_09_100509

Figure 1-9:SP605 X2 Oscillator Pin 1 Location Identifiers

24	www.xilinx.com	SP605 Hardware User Guide
		UG526 (v1.1.1) February 1, 2010

Image 24

Contents SP605 Hardware User Guide UG526 v1.1.1 February 1, 2010 optionalRevision History Date Version RevisionTable of Contents SP605 Hardware User Guide About This Guide Additional Support Resources Preface About This GuideSP605 Evaluation Board Additional InformationFeatures SP605 Evaluation BoardBlock Diagram OverviewSP605 Features FeatureDetailed Description SP605 Features Cont’d Configuration SP605 Evaluation Board SP605 Features Cont’dSpartan-6 XC6SLX45T-3FGG484 Fpga MB DDR3 Component Memory Voltage RailsDetailed Description 2I/O Voltage Rail of Fpga BanksSchematic Net Name Memory U42 Pin Pin Number Pin Name 5DDR3 Component Memory ConnectionsU1 Fpga SPI x4 Flash 3J17 SPI Flash Programming HeaderSchematic Net Name Detailed Description 6SPI x4 Memory ConnectionsLinear BPI Flash Pin Number Pin NameFLASHA16 System ACE CF and CompactFlash Connector Fpga Design Considerations for the Configuration Flash8System ACE CF Connections U1 Fpga Pin Schematic Net Name1 U17 XCCACETQ144IUSB Jtag Clock Generation Oscillator DifferentialOscillator Socket Single-Ended, 2.5V or 8SP605 X2 Oscillator Socket Pin 1 Location IdentifiersSMA Connectors Differential Multi-Gigabit Transceivers GTP MGTsMGT Refclk Smarefclkn 11PCIe Edge Connector Connections U1 Fpga Pin P4 PCIe Edge ConnectorPCI Express Endpoint Connectivity References SFP Module Connector Sfpclkqop14PHY Configuration Pins 11 /100/1000 Tri-Speed Ethernet PHYBit2 Bit1 Bit0 15Ethernet PHY Connections U1 Fpga PinPHYRXD7 USB-to-UART Bridge 17 USB-to-UART ConnectionsDVI Codec IIC Bus 11IIC Bus TopologyKb NV Memory IicsclsfpIicsdamain SDA Signal Name Color Label Description Status LEDsEthernet PHY Status LEDs 13Ethernet PHY Status LEDsFpga Init and Done LEDs 22 Fpga Init and Done LED ConnectionsUser I/O User LEDs23User LED Connections U1 Fpga Pin Controlled LEDUser Pushbutton Switches SW6User DIP Switch User SIP Header U1 Fpga PinUser SMA Gpio Usersmagpion UsersmagpiopSwitches Power On/Off Slide Switch SW2Sysaceresetb Pushbutton SW9 Active-Low Fpgaprogb Pushbutton SW3 Active-Low23System ACE CF CompactFlash Image Select DIP Switch S1 Mode DIP Switch SW1 Active-High 24FPGA Mode DIP Switch SW1Vita 57.1 FMC LPC Connector 28VITA 57.1 FMC LPC Connections LPC PinPower Management AC Adapter and 12V Input Power Jack/SwitchOnboard Power Regulation Power ManagementUCD9240PFC Configuration Options 30SP605 Fpga Configuration Modes M10 Bus WidthConfiguration Solution User Guide Section SP605 Evaluation Board Table A-1Default Switch Settings Function/Type DefaultFMC Jtag Vita 57.1 FMC LPC Connector Pinout Appendix B Vita 57.1 FMC LPC Connector Pinout SP605 Master UCF Appendix C SP605 Master UCF NET FmcpwrgoodflashrstbNET Fpgacmpcsb NET MEM1LDQSN LOC NET Sysclkn Appendix C SP605 Master UCF References