Canon DR-5060F manual Preparation Before Use

Page 29

6

7

8

Draw out the film, and insert the tip of the film into the take-up reel with the number “1” written on the reel face up.

Place the take-up reel on the shaft.

Turn the reel a few times in the direction of the arrow, and make sure that the film is firmly taken up on the reel while taking up any slack in the film at the same time.

2

Preparation Before Use

Handling the Camera Unit 27

Image 29

Contents

Instructions FCC Regulations For 120V models Introduction Filmer This UnitScanner Contents Specifications Options Consumables Chapter TroubleshootingChapter Daily Cleaning Daily maintenance Safety PrecautionsSafety Precautions About the Installation Location Carrying About the Power SupplyChapter Features of DR-5060F About DR-5060F Packaging What’s in the Box?Front view Names and Functions of PartsRear view Inside with upper unit openFunction keys Remaining film indicatorOperation panel Space/Trailer key Backup keyCount Only key New File keyStart key Indicator lampsFeeding Option key Brightness keyFunction key labels Removable trayDocument eject support plate About the Camera Unit Preparation Before Use System Requirements Preparation Before Use Connecting to a ComputerConnecting the Scsi Cable Setting the Scsi ID Setting the Scsi ID and TerminatorSetting the terminator Connecting the power cord Connecting the Power Cord and Ground CableLoading Film Handling the Camera UnitPress the release notch to open the camera unit’s cover Take the microfilm out of its caseClose the left cover taking care not to nip the film Preparation Before Use Close the cover, and make sure that it is locked Affixing the Index LabelPush the camera unit down onto the main unit Loading the Camera Unit in the DR-5060FRemoving the Camera Unit Press the release notch to open the cover on the right Removing FilmRemove the film Store the film in its case Document tray extension Preparing for Paper Feed and EjectAffixing the Document Guide Labels Document eject tray extension Open the extension wireDocument eject support plate Paper Feed Adjustment Turning the Power on Turning the Power ON/OFFTo turn this unit ON, press the power switch Turn the computer onTurn the computer OFF before you turn the scanner OFF Turning the Power OFFPreparing Documents Backup key lit Backup mode Checking the Operation ModeBackup key out Scanner Only mode Backup key blinking Filmer Only modeWhen counting ends, press the Count Only key to cancel Count Only key lit Count Only modeCount Only mode Preparing DocumentsTypes of Documents About DocumentsDocument Loading Precautions Setting Scan Conditions Selecting the Feeding Option Remote Semi-Auto Is lowered when scanning of all pages in the document endsSemi-Auto Inserted first into the scannerAuto Sensor Manual To end scanning, press the Stop key Insert the document one page at a timeFunction Key Settings Press the blinking function key again Manual Thickness AdjustmentPress the or key to adjust the paper thickness Double Feed Detection Fixed Thickness ModeImprinter Restore Memorized SettingFilm Density Odometer IndicationUser Mode Setup Items Setting in the User ModeSpace feed setting Endorser stamp mode settingLeader feed setting Trailer settingSelect the user mode address using the or key How to Set the User modeWhen the final letter of the user mode setting is a number When the final letter of the user mode setting isTroubleshooting When the Scanner is Not Recognized Removing Paper Jams TroubleshootingPaper Jam in the Paper Eject Section Eject tray extension if it is openPage Check the intermediate unit for jammed paper Paper Jam in the Feed SectionRemove the jammed paper from the feed section Press the open/close button, and lift up the feed unitGently close the upper unit Removing the Intermediate Unit Push the intermediate unit down Attaching the Intermediate UnitCondition Paper jam has occurred Paper Feed TroubleCondition Double feed cannot be detected Cause Scanning glasses and rollers on the scanner are dirty When the Scanned Image is Not NormalCause Scan conditions are inappropriate Cause Driver or application does not run correctlyWhen an Error Code is Displayed Cause Endorser option connection error Cause Optional imprinter’s ink cartridge is not installedCause Lamp has reached the end of its service life Cause Document was skewedDaily Cleaning Cleaning the Main Unit Daily CleaningDaily Cleaning Cleaning the Scanning Glasses and RollersOpen the feed unit Use a clean, dry cloth to wipe the scanning glasses Lower the lever Press this part Fit into Deeper Two grooves Memo Power Cord Cleaning the Camera UnitImprinter Guide Plate SCSI-II SpecificationsEndorser ED600 Camera unitImprinter Bar code decoderPage CANON Electronics INC

Related manuals

Manual 92 pages 34.67 Kb