Canon DR-5060F manual Sensor

Page 51

5 The document tray automatically rises, and scanning begins. The document tray is lowered when scanning of all pages in the document ends.

CAUTION

If the document tray does not rise after loading documents on the document tray and you hear a clicking sound, a probable cause is that the document stack weight is heavier than specified even if the load is lower than specified (below the mark on the document tray). Reduce the number of pages to load on the document tray, and try scanning again.

NOTE

When the Feeding Option key is set to “Auto”, the sensor at the location in the figure below automatically detects the document to start scanning.

If the sensor is obstructed after start of scanning is instructed, the DR-5060F mistakenly judges that a document has been loaded, and the document tray automatically starts to move. So, prevent the sensor from being obstructed by objects other than documents.

Feeding Option
Manual
Auto	Sensor
Semi-Auto

Scanning will not start if the document is loaded beforehand. In this case, either press the Start key, or remove the document and then load it again.

If a system error or paper jam stops feeding of the document during scanning, clear the paper jam, and then check that the image of the last ejected page of the document is correctly transferred to computer before continuing scanning.

6 If there are more documents to scan, load the document, and scanning begins automatically. To end scanning in the Backup mode or Scanner Only mode, press the Clear/Stop key.

3

Preparing Documents

Setting Scan Conditions 49

Image 51

Contents

Instructions FCC Regulations For 120V models Introduction This Unit ScannerFilmer Contents Chapter Troubleshooting Chapter Daily CleaningSpecifications Options Consumables Daily maintenance Safety PrecautionsSafety Precautions About the Installation Location Carrying About the Power SupplyChapter Features of DR-5060F About DR-5060F Packaging What’s in the Box?Front view Names and Functions of PartsRear view Inside with upper unit openRemaining film indicator Operation panelFunction keys New File key Backup keySpace/Trailer key Count Only keyBrightness key Indicator lampsStart key Feeding Option keyRemovable tray Document eject support plateFunction key labels About the Camera Unit Preparation Before Use System Requirements Connecting to a Computer Connecting the Scsi CablePreparation Before Use Setting the Scsi ID Setting the Scsi ID and TerminatorSetting the terminator Connecting the power cord Connecting the Power Cord and Ground CableTake the microfilm out of its case Handling the Camera UnitLoading Film Press the release notch to open the camera unit’s coverClose the left cover taking care not to nip the film Preparation Before Use Close the cover, and make sure that it is locked Affixing the Index LabelPush the camera unit down onto the main unit Loading the Camera Unit in the DR-5060FRemoving the Camera Unit Press the release notch to open the cover on the right Removing FilmRemove the film Store the film in its case Preparing for Paper Feed and Eject Affixing the Document Guide LabelsDocument tray extension Document eject tray extension Open the extension wireDocument eject support plate Paper Feed Adjustment Turn the computer on Turning the Power ON/OFFTurning the Power on To turn this unit ON, press the power switchTurn the computer OFF before you turn the scanner OFF Turning the Power OFFPreparing Documents Backup key blinking Filmer Only mode Checking the Operation ModeBackup key lit Backup mode Backup key out Scanner Only modePreparing Documents Count Only key lit Count Only modeWhen counting ends, press the Count Only key to cancel Count Only modeTypes of Documents About DocumentsDocument Loading Precautions Setting Scan Conditions Selecting the Feeding Option Remote Inserted first into the scanner Is lowered when scanning of all pages in the document endsSemi-Auto Semi-AutoAuto Sensor Manual To end scanning, press the Stop key Insert the document one page at a timeFunction Key Settings Manual Thickness Adjustment Press the or key to adjust the paper thicknessPress the blinking function key again Double Feed Detection Fixed Thickness ModeOdometer Indication Restore Memorized SettingImprinter Film DensityUser Mode Setup Items Setting in the User ModeTrailer setting Endorser stamp mode settingSpace feed setting Leader feed settingWhen the final letter of the user mode setting is How to Set the User modeSelect the user mode address using the or key When the final letter of the user mode setting is a numberTroubleshooting When the Scanner is Not Recognized Eject tray extension if it is open TroubleshootingRemoving Paper Jams Paper Jam in the Paper Eject SectionPage Check the intermediate unit for jammed paper Paper Jam in the Feed SectionRemove the jammed paper from the feed section Press the open/close button, and lift up the feed unitGently close the upper unit Removing the Intermediate Unit Push the intermediate unit down Attaching the Intermediate UnitCondition Paper jam has occurred Paper Feed TroubleCondition Double feed cannot be detected Cause Driver or application does not run correctly When the Scanned Image is Not NormalCause Scanning glasses and rollers on the scanner are dirty Cause Scan conditions are inappropriateWhen an Error Code is Displayed Cause Document was skewed Cause Optional imprinter’s ink cartridge is not installedCause Endorser option connection error Cause Lamp has reached the end of its service lifeDaily Cleaning Cleaning the Main Unit Daily CleaningDaily Cleaning Cleaning the Scanning Glasses and RollersOpen the feed unit Use a clean, dry cloth to wipe the scanning glasses Lower the lever Press this part Fit into Deeper Two grooves Memo Power Cord Cleaning the Camera UnitImprinter Guide Plate SCSI-II SpecificationsBar code decoder Camera unitEndorser ED600 ImprinterPage CANON Electronics INC

Related manuals

Manual 92 pages 34.67 Kb