Canon DR-5060F manual Imprinter, Film Density, Odometer Indication, Address Indication

Page 57

■Imprinter

When the optional imprinter is installed on the scanner, you can select whether or not to use the imprinter by a function key.

To enable use of the imprinter, press the function key to which the imprinter is registered, and scan the document with the key lamp lit.

To disable use of the imprinter, scan the document with the key lamp out.

■Film Density

Select the photographic density of the film within the range -3 to +3, and register it to a function key. Normally, “0” is set as the film density.

MEMO

The density must sometimes be adjusted according to the film or developer you are using. For details, contact a Canon service department.

■Odometer Indication

If you press the function key to which odometer indication is registered, the function key lamp lights, and the counter display indicates “-odo-”. This display then changes to indicate the odometer level of the currently loaded camera unit. The odometer level is indicated within the range 00000 to 65535, and the odometer level numerical value is held in DR-5060F memory even if the camera unit is replaced or the main unit is turned OFF. To reset the odometer indication, hold down the Clear/Stop function key for about two seconds with the odometer level displayed.

■Page Address Indication

If you press the function key to which page address indication is registered, the function key lamp blinks, and the counter display indicates “-P-”. This display then changes to indicate the page address of the currently loaded camera unit. The page address is indicated within the range 00000 to 99999, and the page address numerical value is held in DR-5060F memory even if the camera unit is replaced or the main unit is turned OFF. To clear the page address indication, hold down the Clear/Stop function key for about two seconds with the page address displayed. The file address is also cleared by this operation.

■File Address Indication

If you press the function key to which file address indication is registered, the function key lamp blinks, and the counter display indicates “-F-”. This display then changes to indicate the file address of the currently loaded camera unit. The file address is indicated within the range 00000 to 99999, and the file address numerical value is held in DR-5060F memory even if the camera unit is replaced or the main unit is turned OFF. To clear the file address indication, hold down the Clear/Stop function key for about two seconds with the file address displayed. The page address is also cleared by this operation.

■Restore Memorized Setting

Different settings can be registered to each of the function keys, so that you can store settings matched to specific originals.

To use registered scanner settings, press the key to which the desired scanner settings are registered, and the document with the key lamp lit.

3

Preparing Documents

Setting Scan Conditions 55

Page 56 Page 58
Image 57
Page 56 Page 58
Contents
Instructions FCC Regulations For 120V models Introduction This Unit ScannerFilmer Contents Chapter Troubleshooting Chapter Daily CleaningSpecifications Options Consumables Daily maintenance Safety PrecautionsSafety Precautions About the Installation Location Carrying About the Power SupplyChapter Features of DR-5060F About DR-5060F Packaging What’s in the Box?Front view Names and Functions of PartsRear view Inside with upper unit openRemaining film indicator Operation panelFunction keys Space/Trailer key Backup keyCount Only key New File keyStart key Indicator lampsFeeding Option key Brightness keyRemovable tray Document eject support plateFunction key labels About the Camera Unit Preparation Before Use System Requirements Connecting to a Computer Connecting the Scsi CablePreparation Before Use Setting the Scsi ID Setting the Scsi ID and TerminatorSetting the terminator Connecting the power cord Connecting the Power Cord and Ground CableLoading Film Handling the Camera UnitPress the release notch to open the camera unit’s cover Take the microfilm out of its caseClose the left cover taking care not to nip the film Preparation Before Use Close the cover, and make sure that it is locked Affixing the Index LabelPush the camera unit down onto the main unit Loading the Camera Unit in the DR-5060FRemoving the Camera Unit Press the release notch to open the cover on the right Removing FilmRemove the film Store the film in its case Preparing for Paper Feed and Eject Affixing the Document Guide LabelsDocument tray extension Document eject tray extension Open the extension wireDocument eject support plate Paper Feed Adjustment Turning the Power on Turning the Power ON/OFFTo turn this unit ON, press the power switch Turn the computer onTurn the computer OFF before you turn the scanner OFF Turning the Power OFFPreparing Documents Backup key lit Backup mode Checking the Operation ModeBackup key out Scanner Only mode Backup key blinking Filmer Only modeWhen counting ends, press the Count Only key to cancel Count Only key lit Count Only modeCount Only mode Preparing DocumentsTypes of Documents About DocumentsDocument Loading Precautions Setting Scan Conditions Selecting the Feeding Option Remote Semi-Auto Is lowered when scanning of all pages in the document endsSemi-Auto Inserted first into the scannerAuto Sensor Manual To end scanning, press the Stop key Insert the document one page at a time Function Key Settings Manual Thickness Adjustment Press the or key to adjust the paper thicknessPress the blinking function key again Double Feed Detection Fixed Thickness ModeImprinter Restore Memorized SettingFilm Density Odometer IndicationUser Mode Setup Items Setting in the User ModeSpace feed setting Endorser stamp mode settingLeader feed setting Trailer settingSelect the user mode address using the or key How to Set the User modeWhen the final letter of the user mode setting is a number When the final letter of the user mode setting isTroubleshooting When the Scanner is Not Recognized Removing Paper Jams TroubleshootingPaper Jam in the Paper Eject Section Eject tray extension if it is openPage Check the intermediate unit for jammed paper Paper Jam in the Feed SectionRemove the jammed paper from the feed section Press the open/close button, and lift up the feed unitGently close the upper unit Removing the Intermediate Unit Push the intermediate unit down Attaching the Intermediate UnitCondition Paper jam has occurred Paper Feed TroubleCondition Double feed cannot be detected Cause Scanning glasses and rollers on the scanner are dirty When the Scanned Image is Not NormalCause Scan conditions are inappropriate Cause Driver or application does not run correctlyWhen an Error Code is Displayed Cause Endorser option connection error Cause Optional imprinter’s ink cartridge is not installedCause Lamp has reached the end of its service life Cause Document was skewedDaily Cleaning Cleaning the Main Unit Daily CleaningDaily Cleaning Cleaning the Scanning Glasses and RollersOpen the feed unit Use a clean, dry cloth to wipe the scanning glasses Lower the lever Press this part Fit into Deeper Two grooves Memo Power Cord Cleaning the Camera UnitImprinter Guide Plate SCSI-II SpecificationsEndorser ED600 Camera unitImprinter Bar code decoderPage CANON Electronics INC
Related manuals
Manual 92 pages 34.67 Kb
Top Page Image Contents