Mitsubishi Electronics HS-HD2000U manual Operating Your Remote Control, Playback

Page 15

Playback

3You are now watching the VCRÕs picture. To go back to viewing the picture from the TV, press the TVÕs INPUT button to go back to the previous ANTENNA input position.

4Later, you should turn the RF converter OFF by following instructions on page 61.

If your system includes a home theater receiver or an A/V receiver, refer to your home theater receiverÕs ownerÕs guide.

TV without Audio/Video Inputs

If your TV does not have separate audio/video inputs, then your VCR will need to convert the VCRÕs picture to channel 3 or 4. This is called the video channel. The factory has already selected channel 3; however, if it is a broadcast channel in your area, then you will need to change this to channel 4. To make this change:

set up

1To choose channel 4: with VCR power OFF, turn the front panel jog dial disk clockwise while holding down the SP/EP button on the front panel. Ant ch 4 will display on the front panel and the VCR will send signals on channel 4.

If needed, to return to channel 3: with the VCR turned OFF, turn the jog dial

POWER SP/EP

counter-clockwise while holding down the SP/EP button on the front panel.

 

 

 

 

 

 

Ant ch 3 will display.

 

 

 

2 Turn the VCR on by pressing POWER. operating

3Check to see if the VCR light on the front panel display is lit. If it is not, press VCR/TV on the remote control until the VCR light appears on the front panel. This light must be on when you watch a video tape or use the VCR menus.

The VCR light will turn on automatically when you play a tape or use the VCR menus when the RF converter is set to ON. See page 61.

4Turn on the TV and change the TV to the video channel (3 or 4). You are now watching the VCRÕs picture.

To watch a channel that is different than the channel your VCR is recording, the VCR light must be off. The VCR/TV button turns this light on and off.

Operating Your Remote Control

Installing the Batteries

1To remove the back cover, press the ridged area gently, then push the cover in the direction of the arrow and lift.

2Load the batteries, making sure the polarities (+) and (Ð) are correct. This is marked inside the battery compartment.

Next, you need to tell the remote control to operate the VCR, not the TV.

Operating the VCR with the Remote Control

The HS-HD2000U has two VCR remote control operational settings: VCR-A and VCR-B. The HS-HD2000U is pre-set to VCR-A setting. See page 65 for informa- tion about VCR operational setting.

1Set the VCR/TV slide switch on the remote control to VCR position. This ÒtellsÓ the remote that you want to control the VCR.

Now your remote is ready to operate your HS-HD2000U. If the VCR does not respond to the remote, please see page 65.

VCR/TV

JOG/CHANNEL

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Video Cassette Recorder Ownerõs Guide Refer Servicing to Qualified Service Personnel Special Features HS-HD2000UShortcuts Read Instructions CleaningAccessories Power SourcesOverloading Power LinesReplacement Parts Safety CheckHooking Up Your VCR Unpacking Your VCRChoosing a Hookup Antenna or Cable System without Cable Box Antenna or Cable System with Cable BoxHooking Up Your VCR Connections to TV with Audio Video Inputs Ieee 1394-equipped Hdtv receiver Correct Optional Connections to Satellite ReceiverConnections to Home Theater Receiver Connections to IR Emitter Displaying 1394 connection list PlaybackConnection list TV with Audio/Video InputsPlayback Operating Your Remote ControlInstalling the Batteries Operating the VCR with the Remote ControlPlaying a Tape Recorded in Analog S-VHS/S-VHS ET/VHS Format Loading a TapePlaying a Tape Playing a Tape Recorded in D-VHS FormatUnloading a Tape Using Basic Playback ControlsUsing ALLSETª to Set Up Your VCR Automatically Setting Up Your VCRSetting Up Your VCR If you choose Cable or Indoor/outdoor antIf you choose Cable box only or Digital cable box only Cancel NBC OFF Satellite Receiver ControlÅSet the clock ÇAdd/delete channels Adding and Deleting ChannelsSelecting satellite channels sequentially Selecting a ChannelDigital cable box Selecting antenna, cable or digital cable channels directlySetting the Auto Clock Setting the ClockIf the VCR displays the wrong time Setting the Clock ManuallyÄMonth REC Recording copy protected digital programs RecordingSP/EP Input Channel Using One-Touch Recording OTR If you program too much time into the OTR timerHow OTR affects other controls How OTR2 affects other controls Using Standby One-Touch Recording OTR2To cancel OTR2 Channel on the cable boxRecording Mode Recording FormatRecording Time If you use VHS tape for recording Using S-VHS Set-Up MenuSelecting Recording Format If you use S-VHS tape for recordingUsing S-through Selecting S-input SettingNormal recording Record Using Audio and Video FunctionsDescriptions of Audio Functions Audio monitor Listen toDescriptions of Video Functions Selecting and Adjusting the Audio and Video Functions VHS Timer Recording Timer RecordingWhen you program both the D-VHS and analog timer recording Timer RecordingCH DAY on OFF Conventional VCR Timer Recording Changing while Programming Cancelling a Recording in ProgressVCR Plus+¨ System Programming VCR Plus+ System Programming Using the On Screen DisplayVCR Plus+ System Programming Using the Remote Control LCD Timer Recording Quick Program Quick ProgramOn LCD Programming Timer Recording Hints Program Caution Auto Speed ProgrammingTV Programs that End on the Day After Program Skip Using MenusProgram Skip Using the Power Button Changing Timer Recording SettingsCancelling a Timer Recording before the Recording Starts Using a Satellite ReceiverMemory Backup Copying a Tape from D-VHS to D-VHS Editing FeaturesCopying a Tape from D-VHS to Analog Editing FeaturesCopying a Tape from Analog to Analog Using the HS-HD2000U to Record from Another VCRRecording Using the HS-HD2000U to Playback to Another VCRAdvanced Features Advanced Playback Controls for analog playback onlySpecial Effects Searching Techniques Adjusting the TrackingAdvanced Features Time CounterSpeed search Quick search CM skipManual index marks Counter zero stopIndex search Automatic index marksSearch to blank Repeat playbackTo make the time gauge and the remaining time appear Displaying the Current Time Customize Choices MenuVideo mute PerfecTape¨ Auto power save auto-offSetting up PerfecTape¨ RF converterUsing PerfecTape¨ automatically Using PerfecTape¨ manuallyRentalXpress Search with Picture Advanced Options Using the remote control to operate your TVSetting up your remote control to operate your TV Operating your TV with the HS-HD2000U remote controlTo program the HS-HD2000U and the remote to VCR-B To program the remote control operational settingWhen you wish to operate the other VCR Child LockLocation of Controls Remote ControlRemote control operational setting Location of Controls Remote Control -- Flip cover openRemote Control LCD Liquid Crystal Display Transfer indicatorLocation of Controls Front Panel Location of Controls Front Panel Display Location of Controls Rear Panel Jacks ¥ Video game patterns and scoreboards Important InformationTrouble Checks Problem Try ThisTrouble Checks Index SpecificationsVHS IndexPage Mitsubishi Video Cassette Recorder Limited Warranty WarrantyFor your nearest Mitsubishi Authorized Service Center call
Top Page Image Contents