Mitsubishi Electronics HS-HD2000U manual Auto Speed Programming, Program Caution

Page 50

Timer Recording

If a tape runs out during timer recording, the VCR ejects the tape and the pro-

grammed recording light (PROG REC ) and the tape status symbol () will flash. Load a new tape and press REC. Recording will resume.

The programmed recording will be cancelled unless you turn the VCR off before the recording starts. Do not use an integrated HDTV or an IEEE 1394-equipped HDTV receiver to turn on or function the VCR while the VCR is in stand-by mode for the timer recording.

If you forget to load a tape, the programmed recording light (PROG REC ) and the tape status symbol () will flash when you turn the VCR power off. (A tape without an

erasure tab will be ejected. To correct this, load a tape with its erasure tab intact, and turn off the VCR.)

Do not overlap the recording times you enter into the VCR. If you set two analog programmed recording times to overlap, VCR is already programmed for that time will appear on your screen. When you set the analog and the D-VHS timer record- ing times overlap, these timer recordings may not be recorded correctly.

Remember that the VCR will record over the next section of tape. If you want to save a tape, remove it and instead use a different tape for a new recording.

Your VCR will not record over a tape that has the erasure prevention tab removed. All rental movies have this tab removed, so they are safe from being accidentally erased.

Auto Speed Programming

Use auto speed programming if you want to record as much of the program as possible in standard play (SP) speed, but you want the VCR to automatically switch to extended play (EP) if there is not enough tape left.

Auto speed programming is only available for one program. In the first slot, the recording speed default is AUTO.

Make sure that the Tape video function matches the length of tape you are using. See Selecting and adjusting the audio and video functions on page 36.

At the point where the recording mode changes from standard play (SP) to ex- tended play (EP), some noise may be in the picture or sound when playing the tape.

Program Caution

If your VCR is set to record in analog format, but the power is still ON within 3 minutes before timer recording starts, this screen will appear to remind you to turn off the VCR.

If the VCR is still turned on 12 seconds before the start time of the recording, that timer recording will be cancelled.

program caution

￿

￿

REC in 3 min ￿ Turn off VCR

48

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Video Cassette Recorder Ownerõs Guide Special Features HS-HD2000U Refer Servicing to Qualified Service PersonnelShortcuts Power Sources CleaningAccessories Read InstructionsSafety Check Power LinesReplacement Parts OverloadingChoosing a Hookup Hooking Up Your VCRUnpacking Your VCR Hooking Up Your VCR Antenna or Cable System without Cable BoxAntenna or Cable System with Cable Box Connections to TV with Audio Video Inputs Ieee 1394-equipped Hdtv receiver Correct Connections to Satellite Receiver OptionalConnections to Home Theater Receiver Connections to IR Emitter TV with Audio/Video Inputs PlaybackConnection list Displaying 1394 connection listOperating the VCR with the Remote Control Operating Your Remote ControlInstalling the Batteries PlaybackPlaying a Tape Recorded in D-VHS Format Loading a TapePlaying a Tape Playing a Tape Recorded in Analog S-VHS/S-VHS ET/VHS FormatUsing Basic Playback Controls Unloading a TapeSetting Up Your VCR Using ALLSETª to Set Up Your VCR AutomaticallyIf you choose Cable box only or Digital cable box only Setting Up Your VCRIf you choose Cable or Indoor/outdoor ant Cancel NBC Satellite Receiver Control OFFAdding and Deleting Channels ÅSet the clock ÇAdd/delete channelsSelecting antenna, cable or digital cable channels directly Selecting a ChannelDigital cable box Selecting satellite channels sequentiallySetting the Clock Setting the Auto ClockSetting the Clock Manually If the VCR displays the wrong timeÄMonth REC Recording Recording copy protected digital programsSP/EP Input Channel How OTR affects other controls Using One-Touch Recording OTRIf you program too much time into the OTR timer Channel on the cable box Using Standby One-Touch Recording OTR2To cancel OTR2 How OTR2 affects other controlsRecording Time Recording ModeRecording Format If you use S-VHS tape for recording Using S-VHS Set-Up MenuSelecting Recording Format If you use VHS tape for recordingSelecting S-input Setting Using S-throughAudio monitor Listen to Using Audio and Video FunctionsDescriptions of Audio Functions Normal recording RecordDescriptions of Video Functions Selecting and Adjusting the Audio and Video Functions Timer Recording VHS Timer RecordingTimer Recording When you program both the D-VHS and analog timer recordingCH DAY on OFF Conventional VCR Timer Recording Cancelling a Recording in Progress Changing while ProgrammingVCR Plus+ System Programming Using the On Screen Display VCR Plus+¨ System ProgrammingVCR Plus+ System Programming Using the Remote Control LCD Timer Recording Quick Program Quick ProgramOn LCD Programming Timer Recording Hints Auto Speed Programming Program CautionChanging Timer Recording Settings Program Skip Using MenusProgram Skip Using the Power Button TV Programs that End on the Day AfterMemory Backup Cancelling a Timer Recording before the Recording StartsUsing a Satellite Receiver Editing Features Copying a Tape from D-VHS to D-VHSEditing Features Copying a Tape from D-VHS to AnalogUsing the HS-HD2000U to Record from Another VCR Copying a Tape from Analog to AnalogUsing the HS-HD2000U to Playback to Another VCR RecordingSpecial Effects Advanced FeaturesAdvanced Playback Controls for analog playback only Time Counter Adjusting the TrackingAdvanced Features Searching TechniquesQuick search CM skip Speed searchAutomatic index marks Counter zero stopIndex search Manual index marksTo make the time gauge and the remaining time appear Search to blankRepeat playback Video mute Displaying the Current TimeCustomize Choices Menu RF converter Auto power save auto-offSetting up PerfecTape¨ PerfecTape¨RentalXpress Using PerfecTape¨ automaticallyUsing PerfecTape¨ manually Search with Picture Operating your TV with the HS-HD2000U remote control Using the remote control to operate your TVSetting up your remote control to operate your TV Advanced OptionsChild Lock To program the remote control operational settingWhen you wish to operate the other VCR To program the HS-HD2000U and the remote to VCR-BRemote Control Location of ControlsTransfer indicator Location of Controls Remote Control -- Flip cover openRemote Control LCD Liquid Crystal Display Remote control operational settingLocation of Controls Front Panel Location of Controls Front Panel Display Location of Controls Rear Panel Jacks Important Information ¥ Video game patterns and scoreboardsProblem Try This Trouble ChecksTrouble Checks Specifications IndexIndex VHSPage Warranty Mitsubishi Video Cassette Recorder Limited WarrantyFor your nearest Mitsubishi Authorized Service Center call
Top Page Image Contents