Kathrein UFD 545 manual Antenna settings, Satellite scan

Page 38

Installation Menu

DiSEqC-setting

The precondition for this setting is that you have made no changes in the DiSEqC (UFO) setup, refer to the section "DiSEqC (UFO) Setup".

When you are in the LNB configuration menu (see above), press the ou

buttons to move the coloured bar to the "HotBird" position, press the -or +button

and by pressing Oconfirm that you wish to add a satellite. The transponder data are now stored and a tick appears after "HotBird" to confirm the setting. You can now set the DiSEqC signal. It serves the purpose of switching between the two

aligned satellites. Press the oubuttons to go to the DiSEqC-1 setting.

Set #1 for ASTRA and #2 for HotBird. Both positions are already preprogrammed. Cascade switches can be set under DiSEqC 2. Refer to the instructions for your receiving system. Factory setting: "---".

Press L4 times to exit the menu. At the same time, the receiver will confirm that the set parameters have been saved.

If a setting is incorrect, you will see the following message on the screen: "Bad or no signal".

Antenna settings

This menu is intended solely for service purposes and, if need be, i.e. if no measuring instrument is available, it can be used to align the antenna (satellite dish).

The satellite can be defined in the first line and the transponder in the second.

The polarization of the received signal and the transmitted symbol rate are shown in the next line.

The bar displays provide an indication of the strength (relative level) of the signal and its quality. However, no conclusions relating to the quality of the antenna system or of the cable connection can be derived from this signal.

Satellite scan

In the satellite scan menu you can instruct the receiver to scan for channels on the satellite. Use the -or +button to set the required satellite. Start the search scan

by pressing O.

38

Image 38

Contents DVB Satellite Receiver Page Foreword Important informationContents Timer Settings Sound Settings Glossary, Abbreviations Glossary of Technical Terms Safety Information Moisture, sunlight, heat Setting-up locationVentilation Mains voltageRear view Controls, Indicators, Displays and ConnectionsFront view Remote control function buttons ChannelSwitching over between Remote Control Command Sets Receiver on the command setAlphanumeric entries Menu conceptButton functions Language selection OSD To connect the receiver Presetting of the receiving systemConnection and Startup Sat-IF connectionModulator connection Inserting batteries in the remote controlLNB supply voltage TV and video recorder connectionFirst steps Switching on for the First TimeFactory setting of the receiver OSD On-Screen Displays Important on-screen displaysReception status digital Channel selectionSelecting a TV channel Switching over to radio channel Reception status analogueSelecting a radio channel by number entry Timer Settings Stereo and two-channel sound reproduction Sound SettingsSetting the volume MuteFavourite channels Channel Lists TV/radioSelecting TV and radio channels last received To sort the channels To delete a channelTo add a channel To add an analogue channel Analogue channel listsTo set up satellites Adding/Removing SatellitesTo enter a satellite name To remove satellitesThis function cannot be selected in analogue mode Current Channel OverviewEntering a password PasswordFactory setting Parental control Operation from the Front Panel Operation in exceptional casesSystem parameters Setting System ParametersLocal time/timer Parental controlTV type Timer menuSummer time Picture formatOSD colour Mod.typMod.Ch OSD-TransInstallation Menu LNB configurationChanging the oscillator frequency Antenna settings Satellite scanTP setup/scan Scan completed Press OK buttonAnalogue transponder DiSEqC UFO setup KHz signalTone burst Preprogramming is not deleted under Reset Analogue Settings Video menuAudio menu HDP modeAudio mode DecoderDe-emphasis Frequency left/rightBandwidth Playback Video Recorder ConnectionRecording Analogue Decoder Connection Modulator receptionTransferring channel list Data Transfer from Receiver to ReceiverPreparation Transferring operating softwareTechnical features Technical ReferenceTechnical data HF featuresAccessories Scart socket assignmentsConnection examples Connection arrangementAnalog Glossary, Abbreviations DVBGlossary of Technical Terms DiSEqCSymbol rate DiSEqC menu ServiceSatellite Index DNRIndex Page Page Page Page 998.6252/0800/ZWT/PF Subject to technical modifications