Kathrein UFD 545 manual Tone burst

Page 42

Installation Menu

Tone burst

Under this menu point, the 22 kHz signal can be set as follows:

Switching statuses of setting:

Switching statuses of setting:

Switching statuses of setting:

22 kHz Signal

 

—> High/Low

 

22 kHz Signal

—> Pos. A/B

 

22 kHz Signal

—> Pos. A/B

 

 

and

 

 

 

 

 

 

and

 

 

 

 

 

and

 

Tone Burst

 

—> Pos. A/B:

 

Tone Burst

 

—> Opt. A/B

 

Tone Burst

 

—> High/Low

Low

 

22 kHz

 

OFF

 

Pos

 

Tone Burst

22 kHz

 

Low

 

Tone Burst

0

High

 

22 kHz

 

ON

 

 

 

 

 

 

 

High

 

Tone Burst

1

Pos. 1

Tone Burst

Pos. 2

Tone Burst

 

 

0

1

1

2

3

4

0OFF

0ON

1OFF

1ON

Pos. 1 Pos. 2

22kHz

22kHz

OFF

ON

DiSEqC

If the receiver is connected to a DiSEqC switchover matrix, you will need to set this menu point to ON.

The switching criteria and the input assignments of the DiSEqC switching matrix must be maintained. Therefore, refer to the description of the switching matrices or contact the installer of the receiving system.

DiSEqC repeat

The DiSEqC command must be repeated if the receiver is operated (cascaded) together with a receiving system with two or more series connected DiSEqC switching matrices.

In this case, switch the menu point "DiSEqC repeat" to 1 or 2.

Factory presetting: OFF

UFO mini

The input frequency of the receiver is fixed in a "user-controlled processing system". The signals from the "user-controlled processing system" are transmitted on this frequency. The reception parameters for channel selection are transferred to the receiving system by means of a DiSEqC command and set accordingly.

The relevant setting that needs to be selected depends on the type of "user- controlled processing system".

The setting should be made according to the data provided in the installation instructions for the "user-controlled processing system".

Remote frequency

If you have set the UFO mini menu point to "ON" or "OFF", you will need to set the transmission frequency under this menu point.

Refer to the installation instructions of the "user-controlled processing system" for the set transmission frequency.

It is therefore important that you refer to the information provided in the installation instructions of the "user-controlled processing system".

UFO micro

The setting under this menu point is also designed for operation of the receiver together with a processing system.

Control and communication between the receiver and the Kathrein UFO micro system takes place on the return of the coaxial cable.

ON must be set under the UFO micro menu point if the receiver is operated together with a UFO micro receiving system.

During installation, the receiving system then assigns a special address to the receiver so that the control instructions that are sent from the receiver to the receiving system for signal selection are also recognized by this system.

A remote frequency need not be set in this operating mode as it is defined by the

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents DVB Satellite Receiver Page Foreword Important informationContents Timer Settings Sound Settings Glossary, Abbreviations Glossary of Technical Terms Safety Information Moisture, sunlight, heat Setting-up locationVentilation Mains voltageControls, Indicators, Displays and Connections Front viewRear view Remote control function buttons ChannelSwitching over between Remote Control Command Sets Receiver on the command setMenu concept Button functionsAlphanumeric entries Language selection OSD To connect the receiver Presetting of the receiving systemConnection and Startup Sat-IF connectionModulator connection Inserting batteries in the remote controlLNB supply voltage TV and video recorder connectionSwitching on for the First Time Factory setting of the receiverFirst steps OSD On-Screen Displays Important on-screen displaysChannel selection Selecting a TV channelReception status digital Switching over to radio channel Reception status analogueSelecting a radio channel by number entry Timer Settings Stereo and two-channel sound reproduction Sound SettingsSetting the volume MuteChannel Lists TV/radio Selecting TV and radio channels last receivedFavourite channels To sort the channels To delete a channelTo add a channel To add an analogue channel Analogue channel listsTo set up satellites Adding/Removing SatellitesTo enter a satellite name To remove satellitesThis function cannot be selected in analogue mode Current Channel OverviewPassword Factory settingEntering a password Parental control Operation from the Front Panel Operation in exceptional casesSystem parameters Setting System ParametersLocal time/timer Parental controlTV type Timer menuSummer time Picture formatOSD colour Mod.typMod.Ch OSD-TransInstallation Menu LNB configurationChanging the oscillator frequency Antenna settings Satellite scan TP setup/scan Scan completed Press OK buttonAnalogue transponder DiSEqC UFO setup KHz signalTone burst Preprogramming is not deleted under Reset Analogue Settings Video menuAudio menu HDP modeAudio mode DecoderFrequency left/right BandwidthDe-emphasis Video Recorder Connection RecordingPlayback Analogue Decoder Connection Modulator receptionTransferring channel list Data Transfer from Receiver to ReceiverPreparation Transferring operating softwareTechnical features Technical ReferenceTechnical data HF featuresAccessories Scart socket assignmentsConnection examples Connection arrangementAnalog Glossary, Abbreviations DVBGlossary of Technical Terms DiSEqCSymbol rate Service SatelliteDiSEqC menu Index DNRIndex Page Page Page Page 998.6252/0800/ZWT/PF Subject to technical modifications
Top Page Image Contents