Kathrein UFD 545 Data Transfer from Receiver to Receiver, Preparation, Transferring channel list

Page 49

Data Transfer from Receiver to Receiver

Your receiver is able to accept data from another receiver via the RS232C socket. For this purpose, the two receivers are mutually connected via a zero modem cable. The transmitting receiver is the master, the receiving receiver the slave.

Preparation

The master and slave are first switched to standby mode and then disconnected from the mains by pressing the power switch.

The data sockets (Item 8, rear of receiver, Page 9) of both receivers are connected with the zero modem cable.

The master is then switched on again.

Transferring channel list

Simultaneously press the ç button (arrow left) and SELECT under the front panel of the master to transfer the channel list.

The slave can now be switched on. The transfer procedure begins.

While loading, the display of the master shows "t001 t002 .. t00n“ while the slave correspondingly shows "r001 r002..r00n“.

The LED display shows "----" during block transfer.

The loading procedure was successful if both receivers show the message "Succ.".

Transferring operating software

Follow the same procedure as described above for the purpose of transferring operating software.

Start transfer of the operating software by simultaneously pressing the è button (arrow right) and SELECT under the front panel of the master.

While loading, the display of the master shows "t001 t002 .. t00n“ while the slave correspondingly shows "r001 r002..r00n“.

The LED display shows "----" during block transfer.

The loading procedure was successful if both receivers show the message "Succ.".

Should transfer problems occur, "F * * *" will appear in the master display where * stands for a numerical value. In this case, check the cable connection and start a new transfer attempt.

The data transfer from receiver to receiver as described above must only be carried out with devices of the same type as otherwise malfunctions or total loss of the operating software may occur.

On no account must the receivers be switched off or the connection interrupted during data transfer. This may otherwise result in data loss, malfunctions or total failure of the operating system.

In all cases wait until the "Succ." or "F * * *“ message appears on the display.

49

Image 49

Contents DVB Satellite Receiver Page Important information ForewordContents Timer Settings Sound Settings Glossary, Abbreviations Glossary of Technical Terms Safety Information Ventilation Setting-up locationMoisture, sunlight, heat Mains voltageFront view Controls, Indicators, Displays and ConnectionsRear view Channel Remote control function buttonsReceiver on the command set Switching over between Remote Control Command SetsButton functions Menu conceptAlphanumeric entries Language selection OSD Connection and Startup Presetting of the receiving systemTo connect the receiver Sat-IF connectionLNB supply voltage Inserting batteries in the remote controlModulator connection TV and video recorder connectionFactory setting of the receiver Switching on for the First TimeFirst steps Important on-screen displays OSD On-Screen DisplaysSelecting a TV channel Channel selectionReception status digital Reception status analogue Switching over to radio channelSelecting a radio channel by number entry Timer Settings Setting the volume Sound SettingsStereo and two-channel sound reproduction MuteSelecting TV and radio channels last received Channel Lists TV/radioFavourite channels To delete a channel To sort the channelsTo add a channel Analogue channel lists To add an analogue channelAdding/Removing Satellites To set up satellitesTo remove satellites To enter a satellite nameCurrent Channel Overview This function cannot be selected in analogue modeFactory setting PasswordEntering a password Parental control Operation in exceptional cases Operation from the Front PanelLocal time/timer Setting System ParametersSystem parameters Parental controlSummer time Timer menuTV type Picture formatMod.Ch Mod.typOSD colour OSD-TransLNB configuration Installation MenuChanging the oscillator frequency Satellite scan Antenna settingsScan completed Press OK button TP setup/scanAnalogue transponder KHz signal DiSEqC UFO setupTone burst Preprogramming is not deleted under Reset Video menu Analogue SettingsAudio mode HDP modeAudio menu DecoderBandwidth Frequency left/rightDe-emphasis Recording Video Recorder ConnectionPlayback Modulator reception Analogue Decoder ConnectionPreparation Data Transfer from Receiver to ReceiverTransferring channel list Transferring operating softwareTechnical Reference Technical featuresHF features Technical dataScart socket assignments AccessoriesConnection arrangement Connection examplesAnalog DVB Glossary, AbbreviationsDiSEqC Glossary of Technical TermsSymbol rate Satellite ServiceDiSEqC menu DNR IndexIndex Page Page Page Page 998.6252/0800/ZWT/PF Subject to technical modifications