Toshiba KV-HD01A manual System Information, Quality High Ntsc, Rate 6 HR, Size POS

Page 15

3.2 System Information

You can display system settings information as shown on Table 3.2 A below at any time by pressing the DISPLAY button. However, when the unit is displaying a decoded image from a multiplexer, you must first switch the unit to encoded image displaying (The pictures is switching swiftly and the light ofMUX/DVR button is off) by pressing theMUX/DVR button. Each sequential press of the DISPLAY button displays a different message detailed in the following example. By default, the unit displays time, date, and an indicating bar of capacity status on a monitor as shown next.

Default display

 

(Capacity Used)

(Capacity Remaining)

 

 

 

 

 

 

09- 05-2001

16:13:02

(Date)

(System Time)

Press the DISPLAY button once; the unit will display the following sample message plus the default display. Press the DISPLAY button again; the unit will not display any OSD message. Press the button one more time to back to the default display.

Table 3.2 A.

 

 

Description of Table 3.2 A

 

 

 

 

(HD1+HD2: 76GB): Total capacity of installed hard disk, 76 GB

HD 1+HD 2: 76G

11.2 HR

(11.2 HR): Total 11.2 hour minimum guaranteed recording

QUALITY: HIGH

NTSC

 

time available. Actual recording time may be

RATE: 6 HR

20 F/S

 

 

longer in everyday use.

 

 

 

 

 

 

 

 

 

(

): Timer record activated

 

 

 

 

(

): Alarm record activated

HD

P

SIZE

POS

(QUALITY: HIGH): Record quality setting, HIGH

(NTSC): NTSC system

1

Y

38 G

2.5%R (P)

(RATE: 6 HR): Setting of Record time mode, 6 hours

2

Y

38 G

0%R (P)

(20 F/S): Record speed setting, 20 fields/sec

3

.

.

 

 

(HD): Hard disk Compartment

 

 

 

 

 

 

 

 

(P): Y Hard disk installed; . No hard disk installed

 

 

 

 

 

 

 

 

(SIZE 38GB): The capacity of the installed hard disk

 

 

 

 

POS: Percentage of system; R: Recording; P: Playback

14

Image 15
Contents Installation Operating Manual Table of Contents Apendix 4. -- Network Viewing SpecificationsLimited Warranty Main MenuFCC Notice Safety PrecautionsManufacturer’s instruction Important Safety Instructions Graphic symbol definitions Symbol MeaningIndication definitions Meaning Disclaimer Observe the following when installingSave Original Packing Materials Important PrecautionsDaily or weekly Maintenance CopyrightsProduct Features Product FeaturesProduct Introduction Front View Description of the FRONT/REAR ViewPower Indicator Indicator of Alarm Recording ModeIndicator of Timer Recording Mode Indicator of Hard Disk StatusRear View Terminal Block Basic Connection InstallationConnecting with a Single Camera or a Quad Processor Connecting with a MultiplexerSize POS System InformationQuality High Ntsc Rate 6 HRUpdating System Software Video format NTSC/PAL selection Ntsc System Configuring Recording SettingsSet up the REC Time Mode when a multiplexer is connected Basic OperationsRecording Operations Manual RecordingPAL System Start END Timer RecordingTimer Main Timer REC Enable TIMER---------------------------- SETMain SET REC Timer REC Schedule Start END REC EnableAlarm Recording Externally triggered Recording60F/S Place Playback Operations Operation StatusFast Forward/Reverse Play Back Picture-by-picture Slow Forward/ReverseSearch Operations Play Back Recorded Video from a HDD of the mobile rackFull List Search Search Alarm list SearchSearch Full List Alarm List Time Search MM DD Year HH MM Time SearchMain Backup ALL to HD Data BackupBackup Operations System GO to Disk Disk Setting Reformat HD 3 UsageSave ENTER/SAVE button Alarm Select Main Backup Alarm to HDDisk Setting Reformat HD 3 Usage Main Backup Part to HD Total 41 M Ready to GO OK CancelKey Lock Operation Archive Clips into Floppy DiskSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Right/Left buttons Main MenuTitle Stamp Time SettingTitle Setting TIME/ Title0600-1600 1200-1800 Record TimerTimer REC Schedule Start ENDREC Setting 60 F/SREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP RS232 Comm SettingNET Enable OFF NET Setting SET Main SET RS232 CommunicationBackup Full Disk REFORMAT/CLEAR Disk SettingFlicker Reduction SystemHD3 Situation StatusSpecifications Ntsc PALJpeg Setup General Command FormatCommunication Protocol Request Time Second Category=0x02 Keys and signalsCommand Types Command Main Category=0x02 Handshake Second Category=0x01Description of System State Set Setup Values Second Category=0x04Set Time Second Category=0x02 Request State Second Category=0x05Appendix 2. -- System Default Slave Backup Incomplete Battery LOWBackup Complete No Entry for BackupKV-HD01A Connecting KV-HD01 to your networkApendix 4. -- Network Viewing System RequirementsOpen Network Viewer Install the browsing software to your PCRJ-45 PIN configuration for Ethernet Physical specification for EthernetPicture B Picture aPgUp & PgUp System status indicatorsViewing Image Play ListQuality Changing The Record & Timer propertiesChanging Record Properties RateAbort Exit Change the Timer propertiesArchive Images to the computer Number of Saving SaveOpen the Image Viewer Stop Viewing a still JPEG-imageQuit PrintDigital Video Recorder