Toshiba KV-HD01A manual Data Backup, Backup Operations, Main Backup ALL to HD

Page 28

4.5 Data Backup

4.5.1 Backup Operations

There are three ways available to duplicate the recorded video from HD 1 and HD 2 to HD 3. Please take the following steps to proceed.

(1) Set HD 3 to BACKUP first. Take the following steps.

Press the SETUP button to enter the setup mode and select the DISK.

Highlight DISK and press the	SAVE
	ENTER
	/

ENTER/SAVE button to enter the DISK SETTING page.

Then set HD 3 USAGE to BACKUP.

MAIN MENU

TIME/ TITLE

RECORD TIMER

RECORD

ALARM

COMMUNICATION

DISK

SYSTEM

GO TO DISK PAGE

DISK SETTING

REFORMAT	----------	HD 1
HD 3 USAGE	----------	BACKUP
BACKUP		REC/PLAY

MAIN PAGE

SET HD 3 USAGE

(2)FULL: Duplicating all the recorded video from HD1 and HD 2 to HD3.

Stay on the DISK SETTING page.

Use the Up/Down buttons to highlight BACKUP; select FULL, then press the ENTER/SAVE button to proceed.

ENTER

/

SAVE

MAIN MENU

TIME/ TITLE RECORD TIMER RECORD ALARM COMMUNICATION DISK

SYSTEM

GO TO DISK PAGE

DISK SETTING

REFORMAT

HD 3 USAGE

BACKUP----------------FULL

ALARM

SELECT

MAIN PAGE

BACKUP ALL TO HD 3

27

Image 28

Contents Installation Operating Manual Table of Contents Specifications Limited WarrantyMain Menu Apendix 4. -- Network ViewingSafety Precautions FCC NoticeManufacturer’s instruction Graphic symbol definitions Symbol Meaning Important Safety InstructionsIndication definitions Meaning Observe the following when installing DisclaimerImportant Precautions Daily or weekly MaintenanceCopyrights Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Description of the FRONT/REAR View Front ViewIndicator of Alarm Recording Mode Indicator of Timer Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Installation Connecting with a Single Camera or a Quad ProcessorConnecting with a Multiplexer Basic ConnectionSystem Information Quality High NtscRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Configuring Recording Settings Set up the REC Time Mode when a multiplexer is connectedBasic Operations Ntsc SystemManual Recording Recording OperationsPAL System Timer Recording Start ENDTIMER---------------------------- SET Main SET REC Timer REC Schedule Start ENDREC Enable Timer Main Timer REC EnableExternally triggered Recording Alarm Recording60F/S Place Operation Status Playback OperationsFast Forward/Reverse Slow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Search OperationsFull List Search Alarm list Search Search Full List Alarm List Time Search MM DD Year HH MMTime Search SearchData Backup Backup OperationsSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDAlarm Select Main Backup Alarm to HD Disk Setting Reformat HD 3 UsageMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonArchive Clips into Floppy Disk Key Lock OperationSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Main Menu Right/Left buttonsTime Setting Title SettingTIME/ Title Title StampRecord Timer TimerREC Schedule Start END 0600-1600 1200-180060 F/S REC SettingREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP Comm Setting NET Enable OFF NET Setting SET Main SET RS232Communication RS232Disk Setting Backup Full Disk REFORMAT/CLEARSystem Flicker ReductionSituation Status HD3Ntsc PAL SpecificationsJpeg General Command Format SetupCommunication Protocol Keys and signals Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Setup Values Second Category=0x04 Set Time Second Category=0x02Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Battery LOW Backup CompleteNo Entry for Backup Backup IncompleteConnecting KV-HD01 to your network Apendix 4. -- Network ViewingSystem Requirements KV-HD01AInstall the browsing software to your PC RJ-45 PIN configuration for EthernetPhysical specification for Ethernet Open Network ViewerPicture a Picture BSystem status indicators Viewing ImagePlay List PgUp & PgUpChanging The Record & Timer properties Changing Record PropertiesRate QualityChange the Timer properties Archive Images to the computerNumber of Saving Save Abort ExitOpen the Image Viewer Viewing a still JPEG-image QuitPrint StopDigital Video Recorder