Toshiba KV-HD01A manual Communication, RS232, Comm Setting, Slave

Page 37

5.5 COMMUNICATION

The COMMUNICATION option is used to configure status of the communication port when the connected with an external device.

MAIN MENU

TIME/ TITLE RECORD TIMER RECORD ALARM COMMUNICATION DISK

SYSTEM

GO TO COMM PAGE

RS232:

COMM SETTING

RS232

 

: SLAVE

NET

ENABLE

: OFF

NET SETTING

: SET

MAIN PAGE

 

SET RS232

 

The RS232 option is used to determine the activation/ deactivation of the RS232 communication port for externally triggered recording. To record video into the hard-disk drive connect the REC exposure contact on the rear panel of the DVR to the switch used to activate the alarm.

MASTER: Sets the KV-HD01A as the master device.

SLAVE: Sets the KV-HD01A as the slave device.

NET ENABLE is used to allow remote users viewing privileges over a network or IP. OFF: Ethernet capability is turned off

ON: Ethernet capability is turned on

NET SETTING is used to set the IP, MASK, and GATEWAY address of the KV-HD01A. SET: Sets the IP,MASK, and GATEWAY addresses of the KV-HD01A

36

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Installation Operating Manual Table of Contents Limited Warranty SpecificationsMain Menu Apendix 4. -- Network ViewingFCC Notice Safety PrecautionsManufacturer’s instruction Graphic symbol definitions Symbol Meaning Important Safety InstructionsIndication definitions Meaning Disclaimer Observe the following when installingDaily or weekly Maintenance Important PrecautionsCopyrights Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Front View Description of the FRONT/REAR ViewIndicator of Timer Recording Mode Indicator of Alarm Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Connecting with a Single Camera or a Quad Processor InstallationConnecting with a Multiplexer Basic ConnectionQuality High Ntsc System InformationRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Set up the REC Time Mode when a multiplexer is connected Configuring Recording SettingsBasic Operations Ntsc SystemManual Recording Recording OperationsPAL System Start END Timer RecordingMain SET REC Timer REC Schedule Start END TIMER---------------------------- SETREC Enable Timer Main Timer REC EnableExternally triggered Recording Alarm Recording60F/S Place Operation Status Playback OperationsFast Forward/Reverse Play Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Search OperationsFull List Search Search Full List Alarm List Time Search MM DD Year HH MM Alarm list SearchTime Search SearchBackup Operations Data BackupSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDDisk Setting Reformat HD 3 Usage Alarm Select Main Backup Alarm to HDMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonArchive Clips into Floppy Disk Key Lock OperationSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Right/Left buttons Main MenuTitle Setting Time SettingTIME/ Title Title StampTimer Record TimerREC Schedule Start END 0600-1600 1200-180060 F/S REC SettingREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP NET Enable OFF NET Setting SET Main SET RS232 Comm SettingCommunication RS232Backup Full Disk REFORMAT/CLEAR Disk SettingFlicker Reduction SystemHD3 Situation StatusNtsc PAL SpecificationsJpeg General Command Format SetupCommunication Protocol Command Types Keys and signalsCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Time Second Category=0x02 Set Setup Values Second Category=0x04Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Backup Complete Battery LOWNo Entry for Backup Backup IncompleteApendix 4. -- Network Viewing Connecting KV-HD01 to your networkSystem Requirements KV-HD01ARJ-45 PIN configuration for Ethernet Install the browsing software to your PCPhysical specification for Ethernet Open Network ViewerPicture B Picture aViewing Image System status indicatorsPlay List PgUp & PgUpChanging Record Properties Changing The Record & Timer propertiesRate QualityArchive Images to the computer Change the Timer propertiesNumber of Saving Save Abort ExitOpen the Image Viewer Quit Viewing a still JPEG-imagePrint StopDigital Video Recorder
Top Page Image Contents