Toshiba KV-HD01A manual Rear View

Page 12

2.2 Rear View

MUX MAIN MONITOR IN Connector:

This BNC connector is used to connect the live video output from a multiplexer to the unit. VIDEO IN Connector:

This BNC connector is used to connect the video output from a camera or a multiplexer to the unit.

S-VIDEO IN Connector:

This connector is used to connect the S-video output from a camera or a multiplexer to the unit.

Terminal Block:

There are 9 exposure contacts on this terminal block including SW. Out, GND, ALM. OUT, FULL, REC, ALM RST, GND, and ALM. IN for connecting with external devices. Please refer to the next section for details.

Power Switch:

To power the unit on or off.

Plug Outlet:

For connecting with an external power supply.

RS-232 Port:

RS-232 communication port for connecting with an external control device. Please refer to APPENDIX 1 for more details.

S-VIDEO OUT Connector:

This provides a S-video signal to a multiplexer. VIDEO OUT Connector:

This provides a composite video signal to a multiplexer. MONITOR Connector:

This provides a composite video or a multiplexer’s live signal if connected to a display device.

10 BASE-T Connector:

This is a standard RJ-45 connector for 10 Mbps Ethernet networks.

NOTE: The DVR only processes the S-VIDEO IN signal when receiving video signals simultaneously from both “S-VIDEO IN ” and “VIDEO IN ” connectors.

11

Image 12

Contents Installation Operating Manual Table of Contents Specifications Limited WarrantyMain Menu Apendix 4. -- Network ViewingSafety Precautions FCC NoticeManufacturer’s instruction Important Safety Instructions Graphic symbol definitions Symbol MeaningIndication definitions Meaning Observe the following when installing DisclaimerImportant Precautions Daily or weekly MaintenanceCopyrights Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Description of the FRONT/REAR View Front ViewIndicator of Alarm Recording Mode Indicator of Timer Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Installation Connecting with a Single Camera or a Quad ProcessorConnecting with a Multiplexer Basic ConnectionSystem Information Quality High NtscRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Configuring Recording Settings Set up the REC Time Mode when a multiplexer is connectedBasic Operations Ntsc SystemRecording Operations Manual RecordingPAL System Timer Recording Start ENDTIMER---------------------------- SET Main SET REC Timer REC Schedule Start ENDREC Enable Timer Main Timer REC EnableAlarm Recording Externally triggered Recording60F/S Place Playback Operations Operation StatusFast Forward/Reverse Slow Forward/Reverse Play Back Picture-by-pictureSearch Operations Play Back Recorded Video from a HDD of the mobile rackFull List Search Alarm list Search Search Full List Alarm List Time Search MM DD Year HH MMTime Search SearchData Backup Backup OperationsSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDAlarm Select Main Backup Alarm to HD Disk Setting Reformat HD 3 UsageMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonKey Lock Operation Archive Clips into Floppy DiskSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Main Menu Right/Left buttonsTime Setting Title SettingTIME/ Title Title StampRecord Timer TimerREC Schedule Start END 0600-1600 1200-1800REC Setting 60 F/SREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP Comm Setting NET Enable OFF NET Setting SET Main SET RS232Communication RS232Disk Setting Backup Full Disk REFORMAT/CLEARSystem Flicker ReductionSituation Status HD3Specifications Ntsc PALJpeg Setup General Command FormatCommunication Protocol Keys and signals Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Setup Values Second Category=0x04 Set Time Second Category=0x02Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Battery LOW Backup CompleteNo Entry for Backup Backup IncompleteConnecting KV-HD01 to your network Apendix 4. -- Network ViewingSystem Requirements KV-HD01AInstall the browsing software to your PC RJ-45 PIN configuration for EthernetPhysical specification for Ethernet Open Network ViewerPicture a Picture BSystem status indicators Viewing ImagePlay List PgUp & PgUpChanging The Record & Timer properties Changing Record PropertiesRate QualityChange the Timer properties Archive Images to the computerNumber of Saving Save Abort ExitOpen the Image Viewer Viewing a still JPEG-image QuitPrint StopDigital Video Recorder