Toshiba KV-HD01A manual 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP, PRE- Alarm

Page 36

ALM TYPE:

The ALM TYPE option is used to set a type of alarm input corresponding to the sensor signal in use.

NO: Normally Open. This is to be used with the type of alarm sensor, whose contact remains open in normal conditions and closes in case of activation.

NC: Normally Close. This is to be used with the type of alarm sensor, whose contact remains closed in normal conditions and opens in case of activation.

ALM DURATION:

The ALM DURATION option is used to set the alarm record mode to record for a certain duration after the alarm has been deactivated. You can select one of the six following options: 0 SEC,

30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP.

Duration Set ting

Alarm recording

Duration

Alarm	Alarm
activated	deactivated
Non-Stop	Alarm recording

			Duration

Alar m		Alarm		R eset
activated		deactivated

PRE- ALARM:

The PRE-ALARM option is used to determine that images prior to an alarm will be recorded into the hard-disk drive. If the alarm-recording rate is set to 60F/S, when an alarm is being triggered the device will record the image prior to the alarm for 3 seconds. If one of the other alarm-recording rates is set, the pre-alarm image recording will be extended to 5 seconds.

ON: Enables pre-alarm recording. OFF: Disables pre-alarm recording.

35

Image 36

Contents Installation Operating Manual Table of Contents Specifications Limited WarrantyMain Menu Apendix 4. -- Network ViewingSafety Precautions FCC NoticeManufacturer’s instruction Important Safety Instructions Graphic symbol definitions Symbol MeaningIndication definitions Meaning Observe the following when installing DisclaimerImportant Precautions Daily or weekly MaintenanceCopyrights Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Description of the FRONT/REAR View Front ViewIndicator of Alarm Recording Mode Indicator of Timer Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Installation Connecting with a Single Camera or a Quad ProcessorConnecting with a Multiplexer Basic ConnectionSystem Information Quality High NtscRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Configuring Recording Settings Set up the REC Time Mode when a multiplexer is connectedBasic Operations Ntsc SystemRecording Operations Manual RecordingPAL System Timer Recording Start ENDTIMER---------------------------- SET Main SET REC Timer REC Schedule Start ENDREC Enable Timer Main Timer REC EnableAlarm Recording Externally triggered Recording60F/S Place Playback Operations Operation StatusFast Forward/Reverse Slow Forward/Reverse Play Back Picture-by-pictureSearch Operations Play Back Recorded Video from a HDD of the mobile rackFull List Search Alarm list Search Search Full List Alarm List Time Search MM DD Year HH MMTime Search SearchData Backup Backup OperationsSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDAlarm Select Main Backup Alarm to HD Disk Setting Reformat HD 3 UsageMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonKey Lock Operation Archive Clips into Floppy DiskSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Main Menu Right/Left buttonsTime Setting Title SettingTIME/ Title Title StampRecord Timer TimerREC Schedule Start END 0600-1600 1200-1800REC Setting 60 F/SREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP Comm Setting NET Enable OFF NET Setting SET Main SET RS232Communication RS232Disk Setting Backup Full Disk REFORMAT/CLEARSystem Flicker ReductionSituation Status HD3Specifications Ntsc PALJpeg Setup General Command FormatCommunication Protocol Keys and signals Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Setup Values Second Category=0x04 Set Time Second Category=0x02Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Battery LOW Backup CompleteNo Entry for Backup Backup IncompleteConnecting KV-HD01 to your network Apendix 4. -- Network ViewingSystem Requirements KV-HD01AInstall the browsing software to your PC RJ-45 PIN configuration for EthernetPhysical specification for Ethernet Open Network ViewerPicture a Picture BSystem status indicators Viewing ImagePlay List PgUp & PgUpChanging The Record & Timer properties Changing Record PropertiesRate QualityChange the Timer properties Archive Images to the computerNumber of Saving Save Abort ExitOpen the Image Viewer Viewing a still JPEG-image QuitPrint StopDigital Video Recorder