Toshiba KV-HD01A manual Alarm list Search, Time Search

Page 27

4.4.2 Alarm list Search

Take the following steps to proceed with the alarm list search function.

(1) Press the SEARCH button to enter the search mode.

(2)Select the ALARM LIST and press the alarm-event recorded video.

ENTER

/

SAVE

ENTER/SAVE button to access the complete list of

(3)Highlight the specific recorded video of your requirement and press the to display the selected video.

ENTER

/

SAVE ENTER/SAVE button

(Key Operation: Press Up/Down buttons to select a video; Press Right / Left

buttons to flip over a page)

 

 

 

 

 

 

 

 

 

SEARCH

 

 

A 2001-02-01

12: 20

 

 

 

 

A 2001-02-01

13:30

 

 

FULL LIST

 

 

A 2001-03-02

14:20

 

 

 

 

 

 

 

 

ALARM LIST

 

 

 

 

 

 

 

TIME SEARCH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.4.3 Time Search

Take the following steps to proceed with the alarm list search function.

(1) Press the SEARCH button to enter the search mode.

(2) Select the TIME SEARCH and press the

ENTER

/

SAVE

page.

 

ENTER/SAVE button to access the time setting

(3) Set the time period you wish to search for the recorded video.

ENTER

/

(4) Press the SAVE ENTER/SAVE button

to start searching and displaying the concerned image.

(5)If no video is found, please return to the time setting page and repeat steps (3) and (4) again for another search.

SEARCH

FULL LIST

ALARM LIST TIME SEARCH

TIME SEARCH

MMDD YEAR HH MM

08 17 2001 00:00

26

Image 27
Contents Installation Operating Manual Table of Contents Apendix 4. -- Network Viewing SpecificationsLimited Warranty Main MenuFCC Notice Safety PrecautionsManufacturer’s instruction Important Safety Instructions Graphic symbol definitions Symbol MeaningIndication definitions Meaning Disclaimer Observe the following when installingSave Original Packing Materials Important PrecautionsDaily or weekly Maintenance CopyrightsProduct Features Product FeaturesProduct Introduction Front View Description of the FRONT/REAR ViewPower Indicator Indicator of Alarm Recording ModeIndicator of Timer Recording Mode Indicator of Hard Disk StatusRear View Terminal Block Basic Connection InstallationConnecting with a Single Camera or a Quad Processor Connecting with a MultiplexerSize POS System InformationQuality High Ntsc Rate 6 HRUpdating System Software Video format NTSC/PAL selection Ntsc System Configuring Recording SettingsSet up the REC Time Mode when a multiplexer is connected Basic OperationsRecording Operations Manual RecordingPAL System Start END Timer RecordingTimer Main Timer REC Enable TIMER---------------------------- SETMain SET REC Timer REC Schedule Start END REC EnableAlarm Recording Externally triggered Recording60F/S Place Playback Operations Operation StatusFast Forward/Reverse Play Back Picture-by-picture Slow Forward/ReverseSearch Operations Play Back Recorded Video from a HDD of the mobile rackFull List Search Search Alarm list SearchSearch Full List Alarm List Time Search MM DD Year HH MM Time SearchMain Backup ALL to HD Data BackupBackup Operations System GO to Disk Disk Setting Reformat HD 3 UsageSave ENTER/SAVE button Alarm Select Main Backup Alarm to HDDisk Setting Reformat HD 3 Usage Main Backup Part to HD Total 41 M Ready to GO OK CancelKey Lock Operation Archive Clips into Floppy DiskSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Right/Left buttons Main MenuTitle Stamp Time SettingTitle Setting TIME/ Title0600-1600 1200-1800 Record TimerTimer REC Schedule Start ENDREC Setting 60 F/SREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP RS232 Comm SettingNET Enable OFF NET Setting SET Main SET RS232 CommunicationBackup Full Disk REFORMAT/CLEAR Disk SettingFlicker Reduction SystemHD3 Situation StatusSpecifications Ntsc PALJpeg Setup General Command FormatCommunication Protocol Request Time Second Category=0x02 Keys and signalsCommand Types Command Main Category=0x02 Handshake Second Category=0x01Description of System State Set Setup Values Second Category=0x04Set Time Second Category=0x02 Request State Second Category=0x05Appendix 2. -- System Default Slave Backup Incomplete Battery LOWBackup Complete No Entry for BackupKV-HD01A Connecting KV-HD01 to your networkApendix 4. -- Network Viewing System RequirementsOpen Network Viewer Install the browsing software to your PCRJ-45 PIN configuration for Ethernet Physical specification for EthernetPicture B Picture aPgUp & PgUp System status indicatorsViewing Image Play ListQuality Changing The Record & Timer propertiesChanging Record Properties RateAbort Exit Change the Timer propertiesArchive Images to the computer Number of Saving SaveOpen the Image Viewer Stop Viewing a still JPEG-imageQuit PrintDigital Video Recorder