Toshiba KV-HD01A manual Basic Operations, Configuring Recording Settings, Ntsc System

Page 18

4. BASIC OPERATIONS

This section shows you how to operate and manage the unit when it gets in the way.

4.1 Configuring Recording Settings

Recording Time settings (Recording Rate and Picture Quality Setting)

Recording time will vary depending on the image size, recording rate, and the capacity of hard-disk drive. This unit ships with a 80GB hard disk for continuous recording from one to eight weeks under most recording conditions. The table below shows recording times based on the 80GB hard-disk drive at certain refresh rates and the corresponding image quality. With one or more hard-disk drives in operation, please calculate the recording time using the table below in accordance with your requirements. For a NTSC unit, for example, if the unit is set to record images with HIGH quality at a 60 fps record rate, normally a 80GB hard-disk drive will be filled in 12 hours (See the gray area in the table). In a 2nd 80GB hard disk drive is added, under the same refresh rate and picture quality, both drives will be filled in 24 hours.

Set up the REC Time Mode when a multiplexer is connected

For optimum image recording and playback when a Multiplexer is used, the record speed of the multiplexer must be correctly adjusted to match the unit. Set the MULTIPLEXER option on the main menu to ON. This can be done one of the two methods detailed below.

(1)If an Toshiba multiplexer is connected for use, you can program the REC time mode of the multiplexer by referring to the table below (each refresh rate refers to one REC time mode).

(2)For a multiplexer other than Toshiba. Please, connect the SW. OUT terminal on the rear panel of the DVR to the multiplexer’s trigger contact. The DVR will provide the timing signal (Negative/Falling) to the multiplexer. Thus, if the DVR changes the recording speed, the multiplexer will automatically adjust the record to match. The DVR doesn’t provide a 2-hour timing signal in NTSC or 3-hour timing signal in PAL.

NTSC System

 

 

 

 

Possible Recording Time HDD=80 Gigabytes

 

 

Refresh Rate (Field/Sec)

60

20

10

5

2.5

1.25

0.625

0.25

0.16

0.125

 

 

 

 

 

 

 

 

 

 

 

 

Image

HIGH

12 hr

36 hr

72 hr

144 hr

288 hr

576 hr

1008 hr

2880 hr

4320 hr

5760 hr

STANDARD

18 hr

54 hr

108 hr

216 hr

432 hr

864 hr

1512 hr

4320 hr

6480 hr

8640 hr

Quality

 

BASIC

24 hr

72 hr

144 hr

288 hr

576 hr

1152 hr

2016 hr

5760 hr

8640 hr

11520 hr

REC Time Mode

2 hr

6 hr

12 hr

24 hr

48 hr

96 hr

168 hr

480 hr

720 hr

960 hr

 

 

 

 

 

 

 

 

 

 

 

REC interval (1/60 sec)

1

3

6

12

24

48

84

240

360

480

 

 

 

 

 

 

 

 

 

 

 

 

17

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation Operating Manual Table of Contents Main Menu SpecificationsLimited Warranty Apendix 4. -- Network ViewingSafety Precautions FCC NoticeManufacturer’s instruction Important Safety Instructions Graphic symbol definitions Symbol MeaningIndication definitions Meaning Observe the following when installing DisclaimerCopyrights Important PrecautionsDaily or weekly Maintenance Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Description of the FRONT/REAR View Front ViewIndicator of Hard Disk Status Indicator of Alarm Recording ModeIndicator of Timer Recording Mode Power IndicatorRear View Terminal Block Connecting with a Multiplexer InstallationConnecting with a Single Camera or a Quad Processor Basic ConnectionRate 6 HR System InformationQuality High Ntsc Size POSUpdating System Software Video format NTSC/PAL selection Basic Operations Configuring Recording SettingsSet up the REC Time Mode when a multiplexer is connected Ntsc SystemRecording Operations Manual RecordingPAL System Timer Recording Start ENDREC Enable TIMER---------------------------- SETMain SET REC Timer REC Schedule Start END Timer Main Timer REC EnableAlarm Recording Externally triggered Recording60F/S Place Playback Operations Operation StatusFast Forward/Reverse Slow Forward/Reverse Play Back Picture-by-pictureSearch Operations Play Back Recorded Video from a HDD of the mobile rackFull List Search Time Search Alarm list SearchSearch Full List Alarm List Time Search MM DD Year HH MM SearchSystem GO to Disk Disk Setting Reformat HD 3 Usage Data BackupBackup Operations Main Backup ALL to HDMain Backup Part to HD Total 41 M Ready to GO OK Cancel Alarm Select Main Backup Alarm to HDDisk Setting Reformat HD 3 Usage Save ENTER/SAVE buttonKey Lock Operation Archive Clips into Floppy DiskSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Main Menu Right/Left buttonsTIME/ Title Time SettingTitle Setting Title StampREC Schedule Start END Record TimerTimer 0600-1600 1200-1800REC Setting 60 F/SREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP Communication Comm SettingNET Enable OFF NET Setting SET Main SET RS232 RS232Disk Setting Backup Full Disk REFORMAT/CLEARSystem Flicker ReductionSituation Status HD3Specifications Ntsc PALJpeg Setup General Command FormatCommunication Protocol Command Main Category=0x02 Handshake Second Category=0x01 Keys and signalsCommand Types Request Time Second Category=0x02Request State Second Category=0x05 Set Setup Values Second Category=0x04Set Time Second Category=0x02 Description of System StateAppendix 2. -- System Default Slave No Entry for Backup Battery LOWBackup Complete Backup IncompleteSystem Requirements Connecting KV-HD01 to your networkApendix 4. -- Network Viewing KV-HD01APhysical specification for Ethernet Install the browsing software to your PCRJ-45 PIN configuration for Ethernet Open Network ViewerPicture a Picture BPlay List System status indicatorsViewing Image PgUp & PgUpRate Changing The Record & Timer propertiesChanging Record Properties QualityNumber of Saving Save Change the Timer propertiesArchive Images to the computer Abort ExitOpen the Image Viewer Print Viewing a still JPEG-imageQuit StopDigital Video Recorder
Top Page Image Contents