Toshiba KV-HD01A manual Situation Status, HD3

Page 40

BUZZER :

The BUZZER option is used to determine the embedded buzzer sounding a tone to signal the following situations. A tone lasts about two seconds long.

Situation	Status
Alarm	Alarm takes place

Video Loss	Video loss takes place

Disk Full	Disk is full

Load Default	Load factory default

Buzzer	Buzzer set to ON

Key Lock	Enable/disable key lock function

HD3	Power on /off mobile rack HDD

Backup	Backup operation complete

Timer	Timer activate/deactivate

HDD	Recording switching between HDD

ON : BUZZER is enabled.

OFF : BUZZER is disabled.

PASSWORD:

The PASSWORD option is used to set a 4 digit number password to prevent any unauthorized re-formatting of the hard disk drives and to use the network viewer.

OLD PASSWORD : Enter the pre-set password (or the standard password if this is the initial setting) to access the password setting system.

NEW PASSWORD : Enter a 4 digit number password of your choosing which will replace the pre-set password (or the standard password “9999”).

DEFAULT :

The DEFAULT option is used to reload the factory default setting.

39

Image 40

Contents Installation Operating Manual Table of Contents Specifications Limited WarrantyMain Menu Apendix 4. -- Network ViewingSafety Precautions FCC NoticeManufacturer’s instruction Graphic symbol definitions Symbol Meaning Important Safety InstructionsIndication definitions Meaning Observe the following when installing DisclaimerImportant Precautions Daily or weekly MaintenanceCopyrights Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Description of the FRONT/REAR View Front ViewIndicator of Alarm Recording Mode Indicator of Timer Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Installation Connecting with a Single Camera or a Quad ProcessorConnecting with a Multiplexer Basic ConnectionSystem Information Quality High NtscRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Configuring Recording Settings Set up the REC Time Mode when a multiplexer is connectedBasic Operations Ntsc SystemManual Recording Recording OperationsPAL System Timer Recording Start ENDTIMER---------------------------- SET Main SET REC Timer REC Schedule Start ENDREC Enable Timer Main Timer REC EnableExternally triggered Recording Alarm Recording60F/S Place Operation Status Playback OperationsFast Forward/Reverse Slow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Search OperationsFull List Search Alarm list Search Search Full List Alarm List Time Search MM DD Year HH MMTime Search SearchData Backup Backup OperationsSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDAlarm Select Main Backup Alarm to HD Disk Setting Reformat HD 3 UsageMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonArchive Clips into Floppy Disk Key Lock OperationSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Main Menu Right/Left buttonsTime Setting Title SettingTIME/ Title Title StampRecord Timer TimerREC Schedule Start END 0600-1600 1200-180060 F/S REC SettingREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP Comm Setting NET Enable OFF NET Setting SET Main SET RS232 Communication RS232Disk Setting Backup Full Disk REFORMAT/CLEARSystem Flicker ReductionSituation Status HD3Ntsc PAL SpecificationsJpeg General Command Format SetupCommunication Protocol Keys and signals Command TypesCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Setup Values Second Category=0x04 Set Time Second Category=0x02Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Battery LOW Backup CompleteNo Entry for Backup Backup IncompleteConnecting KV-HD01 to your network Apendix 4. -- Network ViewingSystem Requirements KV-HD01AInstall the browsing software to your PC RJ-45 PIN configuration for EthernetPhysical specification for Ethernet Open Network ViewerPicture a Picture BSystem status indicators Viewing ImagePlay List PgUp & PgUpChanging The Record & Timer properties Changing Record PropertiesRate QualityChange the Timer properties Archive Images to the computerNumber of Saving Save Abort ExitOpen the Image Viewer Viewing a still JPEG-image QuitPrint StopDigital Video Recorder