Toshiba KV-HD01A manual Alarm Select Main Backup Alarm to HD, Save ENTER/SAVE button

Page 29

ALARM: Duplicating all the alarm-event recorded video from HD 1 and HD 2 to HD 3. Stay on the DISK SETTING page.

Use the Up/Down buttons to highlight BACKUP; select ALARM, then press the ENTER/SAVE button to proceed.

ENTER

/

SAVE

MAIN MENU

TIME/ TITLE RECORD TIMER RECORD ALARM COMMUNICATION DISK

SYSTEM

GO TO DISK PAGE

DISK SETTING

REFORMAT

HD 3 USAGE

BACKUP----------------FULL

ALARM

SELECT

MAIN PAGE

BACKUP ALARM TO HD 3

SELECT: Duplicating a particular recorded video from HD1 and HD 2 to HD3.

Stay on the DISK SETTING page.
Use the	Up/Down buttons		to highlight BACKUP, select SELECT and then press the
SAVE ENTER/SAVE button		to list all the recorded video.
ENTER
/
Press the	Up/Down buttons		to select the desired clip and press the SETUP button to
mark it.
After completing the selection, press the SAVE ENTER/SAVE button				to proceed.
			ENTER

/

MAIN MENU

TIME/ TITLE

RECORD TIMER

RECORD

ALARM

COMMUNICATION

DISK

SYSTEM

A 2001-02-01 12:20 2001-02-01 03:30 +

A 2001-03-02 04:20 + 2001-04-01 13:30

DISK SETTING

REFORMAT

HD 3 USAGE

BACKUP----------------FULL

ALARM

SELECT

MAIN PAGE

BACKUP PART TO HD 3

TOTAL: 41 M

READY TO GO

OK CANCEL

NOTE: If the capacity of HD 3 is not sufficient to store all selected video, a warning message “HD3 SPACE NOT ENOUGH” will be displayed on the screen. Please, insert a larger capacity of hard disk drive or erase some data from the drive and start the process over again.

28

Image 29

Contents Installation Operating Manual Table of Contents Limited Warranty SpecificationsMain Menu Apendix 4. -- Network ViewingFCC Notice Safety PrecautionsManufacturer’s instruction Indication definitions Meaning Important Safety InstructionsGraphic symbol definitions Symbol Meaning Disclaimer Observe the following when installingDaily or weekly Maintenance Important PrecautionsCopyrights Save Original Packing MaterialsProduct Introduction Product FeaturesProduct Features Front View Description of the FRONT/REAR ViewIndicator of Timer Recording Mode Indicator of Alarm Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Connecting with a Single Camera or a Quad Processor InstallationConnecting with a Multiplexer Basic ConnectionQuality High Ntsc System InformationRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Set up the REC Time Mode when a multiplexer is connected Configuring Recording SettingsBasic Operations Ntsc SystemPAL System Recording OperationsManual Recording Start END Timer RecordingMain SET REC Timer REC Schedule Start END TIMER---------------------------- SETREC Enable Timer Main Timer REC Enable60F/S Alarm RecordingExternally triggered Recording Place Fast Forward/Reverse Playback OperationsOperation Status Play Back Picture-by-picture Slow Forward/ReverseFull List Search Search OperationsPlay Back Recorded Video from a HDD of the mobile rack Search Full List Alarm List Time Search MM DD Year HH MM Alarm list SearchTime Search SearchBackup Operations Data BackupSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDDisk Setting Reformat HD 3 Usage Alarm Select Main Backup Alarm to HDMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Key Lock OperationArchive Clips into Floppy Disk Right/Left buttons Main MenuTitle Setting Time SettingTIME/ Title Title StampTimer Record TimerREC Schedule Start END 0600-1600 1200-1800REC Quality REC Setting60 F/S Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP NET Enable OFF NET Setting SET Main SET RS232 Comm SettingCommunication RS232Backup Full Disk REFORMAT/CLEAR Disk SettingFlicker Reduction SystemHD3 Situation StatusJpeg SpecificationsNtsc PAL Communication Protocol SetupGeneral Command Format Command Types Keys and signalsCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Time Second Category=0x02 Set Setup Values Second Category=0x04Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Backup Complete Battery LOWNo Entry for Backup Backup IncompleteApendix 4. -- Network Viewing Connecting KV-HD01 to your networkSystem Requirements KV-HD01ARJ-45 PIN configuration for Ethernet Install the browsing software to your PCPhysical specification for Ethernet Open Network ViewerPicture B Picture aViewing Image System status indicatorsPlay List PgUp & PgUpChanging Record Properties Changing The Record & Timer propertiesRate QualityArchive Images to the computer Change the Timer propertiesNumber of Saving Save Abort ExitOpen the Image Viewer Quit Viewing a still JPEG-imagePrint StopDigital Video Recorder