Toshiba KV-HD01A manual Slow Forward/Reverse, Play Back Picture-by-picture

Page 25

NOTE: The playback speed will be displayed on the screen. However, when playing a recorded video from a multiplexer, the playback speed only display on encoding (multiplexing) mode. Press the MUX / DVR button to switch between decoding and encoding mode.

4.3.2 Slow Forward/Reverse

There are 4 speeds available for a slow playback: 1/2, 1/4, 1/8, 1/16. Follow the instructions below to proceed with a slow playback.

While playing back recorded video at the recorded speed:

(1)Press the PAUSE/STEP button for the slow playback mode.

(2)Forward: Press the FWD button to view the recorded video in the forward direction at a speed faster than the recorded speed. Each subsequent press of the FWD button slows the rate.

(3)Reverse: Press the REV button to view the recorded video in the reverse direction at a speed faster than the recorded speed. Each subsequent press of the REV button slows the rate.

(4)Normal: Press the PLAY button to return to the normal speed of playback.

4.3.3 Play Back Picture-by-picture

While playing back recorded video at the recorded speed:

(1)Press the PAUSE/STEP button for the picture-by-picture mode.

(2)Press the PAUSE/STEP button to display one frame/field of a picture at a time in the forward direction. (When playing back recorded video recorded by a multiplexer, each

sequential press of the PAUSE/STEP button will display each camera in sequence.)

(3)Press the PLAY button to return to the normal speed of playback.

NOTE: A flickering condition of an image occurs while playing back picture-by-picture, please set the FLICKER REDUCTION option to ON in the SYSTEM page of the main menu. However, when this function is activated, a slight loss of picture quality may occur.

24

Image 25
Contents Installation Operating Manual Table of Contents Limited Warranty SpecificationsMain Menu Apendix 4. -- Network ViewingFCC Notice Safety PrecautionsManufacturer’s instruction Graphic symbol definitions Symbol Meaning Important Safety InstructionsIndication definitions Meaning Disclaimer Observe the following when installingDaily or weekly Maintenance Important PrecautionsCopyrights Save Original Packing MaterialsProduct Features Product FeaturesProduct Introduction Front View Description of the FRONT/REAR ViewIndicator of Timer Recording Mode Indicator of Alarm Recording ModeIndicator of Hard Disk Status Power IndicatorRear View Terminal Block Connecting with a Single Camera or a Quad Processor InstallationConnecting with a Multiplexer Basic ConnectionQuality High Ntsc System InformationRate 6 HR Size POSUpdating System Software Video format NTSC/PAL selection Set up the REC Time Mode when a multiplexer is connected Configuring Recording SettingsBasic Operations Ntsc SystemManual Recording Recording OperationsPAL System Start END Timer RecordingMain SET REC Timer REC Schedule Start END TIMER---------------------------- SETREC Enable Timer Main Timer REC EnableExternally triggered Recording Alarm Recording60F/S Place Operation Status Playback OperationsFast Forward/Reverse Play Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Search OperationsFull List Search Search Full List Alarm List Time Search MM DD Year HH MM Alarm list SearchTime Search SearchBackup Operations Data BackupSystem GO to Disk Disk Setting Reformat HD 3 Usage Main Backup ALL to HDDisk Setting Reformat HD 3 Usage Alarm Select Main Backup Alarm to HDMain Backup Part to HD Total 41 M Ready to GO OK Cancel Save ENTER/SAVE buttonArchive Clips into Floppy Disk Key Lock OperationSave to J0001.JPG Save to J0002.JPG Save to J000N.JPG Right/Left buttons Main MenuTitle Setting Time SettingTIME/ Title Title StampTimer Record TimerREC Schedule Start END 0600-1600 1200-180060 F/S REC SettingREC Quality Alarm Setting 30SEC, 1 MIN, 5 MIN, 10 MIN, and NON-STOP NET Enable OFF NET Setting SET Main SET RS232 Comm SettingCommunication RS232Backup Full Disk REFORMAT/CLEAR Disk SettingFlicker Reduction SystemHD3 Situation StatusNtsc PAL SpecificationsJpeg General Command Format SetupCommunication Protocol Command Types Keys and signalsCommand Main Category=0x02 Handshake Second Category=0x01 Request Time Second Category=0x02Set Time Second Category=0x02 Set Setup Values Second Category=0x04Request State Second Category=0x05 Description of System StateAppendix 2. -- System Default Slave Backup Complete Battery LOWNo Entry for Backup Backup IncompleteApendix 4. -- Network Viewing Connecting KV-HD01 to your networkSystem Requirements KV-HD01ARJ-45 PIN configuration for Ethernet Install the browsing software to your PCPhysical specification for Ethernet Open Network ViewerPicture B Picture aViewing Image System status indicatorsPlay List PgUp & PgUpChanging Record Properties Changing The Record & Timer propertiesRate QualityArchive Images to the computer Change the Timer propertiesNumber of Saving Save Abort ExitOpen the Image Viewer Quit Viewing a still JPEG-imagePrint StopDigital Video Recorder