Advanced Operations
Advanced Operations
Buttons and controls with the | mark are disabled when |
the mode select switch is set to NORMAL.
| MODE |
| NORMAL/DJ |
HOT CUE | TOUCH/ |
A | BRAKE |
B | RELEASE/ |
C | START |
REC MODE | JOG MODE |
| |
PLAY/PAUSE |
|
6 |
|
Jog dial
Scratch play
★This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position.
When the jog mode is set to VINYL mode ON, pressing the jog dial’s top panel while rotating the dial will cause audio and video to be output in proportion to the direction and speed of jog dial rotation.
1.Press the JOG MODE select button so that the VINYL mode indicator lights.
2.During playback, press the top of the jog dial.
¶Playback will slow and come to a stop (the time required to com- plete stop can be set independently).
¶If the jog dial is rotated as playback slows but before it has com- pletely stopped, sound will be interrupted suddenly, and will then start again, but in the direction corresponding to the direction the jog dial is rotated in step 3.
3.Rotate the jog dial in the desired direction of playback.
¶Playback will occur in proportion to the direction and speed of jog dial rotation.
4.Release hand from surface of jog dial.
¶Playback will return to its original status (the time required until full acceleration can be set independently).
■To set the deceleration time (time until playback fully stops when jog dial surface is pressed)
Rotate the TOUCH/BRAKE response dial.
¶The time till playback stops changes.
Hot cue
★This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position.
This function allows playback to be started quickly from one of three points (A, B, C), by previous setting of cue point and loop information.
¶Storing to memory may not be possible while the jog dial’s audio/ video memory status display is flashing.
■Setting hot cue point
1.Press the HOT CUE REC MODE button so that the HOT CUE A, B, and C button indicators light red.
2.During playback, pause mode or cue standby mode, find the point you wish to use as the hot cue, and at that point press the button (A, B, or C) in which you wish to store the cue information.
¶The button memory will recorded with the time position data and playback method.
¶The pressed button will flash red for about 2 seconds, then light steadily.
¶During DVD playback, a thumbnail of the hot cue point will be displayed on the preview monitor screen.
¶If the HOT CUE button is pressed during the loop setting mode (while LOOP OUT/OUT ADJUST button and LOOP IN/REALTIME CUE buttons are flashing), the currently playing loop information will be stored in memory.
¶If a memory card is loaded, the data recorded to the HOT CUE button will be stored on the memory card; in this way, the previ- ously set information can be called up quickly when playing the same disc at a later date (☞ P.42).
■Starting a hot cue
1.Press the HOT CUE REC MODE button so that the HOT CUE A, B, and C button indicators light green or orange.
¶Buttons containing stored hot cue points will light green.
¶Buttons containing stored loop information will light orange.
¶Buttons without any stored information will not light.
2.During playback, pause, or cue standby mode, press one of the buttons with stored information (A, B, or C).
¶During playback, pause mode or cue standby mode, if a green or orange lighted button is pressed, playback will begin instantly based on the information recorded in the button. In this case, cue point information stored in the normal CUE button, or loop information stored in the RELOOP/EXIT button will not be overwritten, but remain valid.
¶Pressing a HOT CUE button with stored loop information causes loop playback to begin instantly based on the stored information. In this case, the RELOOP/EXIT button can be used to cancel the loop playback just as with normal loop play, and the LOOP OUT/ OUT ADJUST button can likewise be used to modify the
¶If a memory card is loaded, inserting a disc will allow previously recorded hot cue and loop information for that disc to be restored (☞ P.43).
■To set the acceleration time (time until playback fully re-
gains original speed when hand is released from jog dial surface)
Rotate the RELEASE/START response dial.
¶The time till playback returns to normal speed changes.
Spin play
★This function is not supported when the rear panel mode select switch (MODE NORMAL/DJ) is set to the NORMAL position.
With VINYL mode ON, press the surface of the jog dial, or press the PLAY/PAUSE (6) button to set the unit to pause, then rotate the jog dial quickly; even if you remove your hand from the jog dial, playback will occur in proportion to the direction and speed of the jog dial rotation.
*When playing a DVD that prohibits title or other searches, it may be impossible to begin playback from the hot cue point.
In this case, the prohibited mark will appear in the display and the
similar mark | will appear on the preview monitor screen. |
*In the case of MP3, hot cue is supported only within one and the same folder.
38