Barco R9001280 owner manual Unpacking, Projector dimensions, Barcovision

Page 11

Unpacking and Dimensions

2

 

UNPACKING AND DIMENSIONS

 

 

 

 

 

 

 

 

 

 

 

 

Unpacking

 

To open the banding, pull on the clip as shown in the first drawing.

Pull

To open

Take the projector out of its shipping carton and place it on a table.

For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts.

When using the projector as a table mounted configuration, always mount the 3 supporting feet (see drawing below). These feet are mounted on the same wooden board. Each food contains one metal part and two plastic parts. To remove the feed, first turn out both plastic parts. To remove the metal parts from the board, remove the retaining bolts. Save these bolts because these bolts must be used to mount the feet to the projector. Mount first the metal parts with the removed bolts and turn in then both plastic parts to finish the feed.

Warning : To prevent overheating of the projector as table mounted, always remove the wooden board and turn in the 3 supporting feet to

allow air circulation via the built-in dust filter at the bottom.

Save the original shipping carton and packing material, they will

 

 

 

 

 

come in handy if you ever have to ship your projector. For maximum

 

 

 

 

 

protection, repack your projector as it was originally packed at the

1

2

3

4

3 7 9

factory.

5

 

 

 

 

 

Contents of the shipped box :

-1 BARCOVISION 8200

-1 remote control unit RCU + 9V battery

-1 power cable with outlet plug type CEE7.

-1 owner’s manual

-3 supporting feet (built up in 3 parts)

Projector dimensions

(units : mm)

L

Some examples of lenses :

 

 

Name lens

Lmin

 

Lmax

 

(*)

mm (inch)

mm (inch)

HD(1.2:1)

1072

(42.20) 1087

(42.79)

HD(2.2:1)

1043

(41.06) 1070

(42.12)

HD(3.3:1)

1017

(40.04) 1072

(42.20)

HD(4.0:1)

1022

(40.24) 1162

(45.75)

HD(5:1)

1082

(42.60)

1202

(47.32)

HD(7:1)

1252

(49.29)

1372

(54.02)

HD(1.5-3:1)

1252

(49.29)

1355

(53.35)

HD(3-5.3:1)

 

 

 

 

(*) More info about lenses, see

 

appendix B.

 

 

 

 

5975348 BARCOVISION 8200 210497

 

 

 

2-1

Image 11
Contents Vision Page Date Rev Art. No 280497 R5975348 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Service Mode Mains lead AC Power cord with CEE 7 plug Safety InstructionsInstallation instructions General safety instructions Prescriptions de securite générales Instructions pour l’installation Remarque sur la Sécurité Fédéral communication commission FCC statementOn Repacking On InstallationOn Cleaning On ServicingRé-emballage ’InstallationEntretien et Réparation NettoyageBarcovision Projector dimensionsUnpacking Battery installation in the RCU Which screen type? Installation guidelinesEnvironment What about ambient light ?Inputs and computer video format input compatibility Where to install the projector?How to install a projection lens? Definitions of the Abbreviation on drawingsLocal keypad Location and Functions of ControlFront panel terminology Control Panel TerminologyRCU Remote controlTerminology Installation SET UP System Settings Fuses Power mains cord connectionSwitching on ConnectionsInput module insertion into the projector Switching to stand-by Switching offInput connections Straps on module level Video/S-video input moduleRGB input selection RGB analog input moduleIndication on the input slot menu Component input moduleComponent input selection Input selection RGB3S/RG3sB input moduleSet up of the baud rate for communication with a computer OFF OFF OFF On OFF OFF OFF on OFF Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector address How to use the RCU?Hardware set up of the projector address ControllingHow to control the projector or projectors How to display a projector address?How to program an address into the RCU? Picture controls with direct accessHow to get source information? Software version How to get a summary of your projector?Input selection Source SET UPInstallation of the settings for a input source Enter Edit fileEdit File Options Copy RenameOptions MoveDelete Source Set Up Gain Signal operationsVideo offset Sync Fast/Slow Gain adjustment per colorSmoothness Still video On/OffZoom/pan Screen operationsMoves the window upwards Picture Compresses the picture in the horizontal direction Geometry ConfigureConversion Picture Control in Adjustment Mode 10-1 Service ModeHow to activate the password function? Start up of the Service mode0000 Convergence adjustment of the LCD panelsRed on green convergence Green focusingBlue on green convergence Lamp Run Time History Modify passwordReset Lamp Run Time 10-6 Barcovision 8200 Standard source set up files Standard Source SET UP FilesStandard Source Set Up Files Battery replacement in the RCU Battery Replacement in the RCULenses Focusing the lensLens Cleaning Procedure Lenses Source numbers 90 Source Numbers 90Insert Card