Barco R9001280 owner manual RGB analog input module, RGB input selection

Page 22

Connections

RGB analog input module.

RGB analog input terminals with separate Horizontal and Vertical sync inputs(RGB-HV), with Composite sync input(RGB-S) or with Sync signals on green(RGsB).

Always use an interface when a computer and local monitor have to be connected to the projector. Interfaces to be applied :

DIAGNOSTICS

IR-ACKNO WLEDGED CODE IR-RECEIVER

RS232 OUT

IR-RECEIVED

Universal analog interface.

Order number : R9826100.

RGB 120 MHz analog interface.

Order number : R9826570.

VGA interface

Order number 120V : R9828079.

Order number 230V : R9828070

MAC interface

Order number 120V : R9828059

Order number 230V : R9828050

MAGIK interface

Order number 120V : R9828129

Order number 230V : R9828120

RGBS/RGsB analog : 5 x BNC Red : 0.7 Vpp ± 3 dB

Blue : 0.7 Vpp ± 3 dB

Green : 0.7 Vpp ± 3 dB

1 Vpp ± 3 dB if sync on green Vert. sync : 1 Vpp to 4 Vpp ± 3 dB Hor. sync / Composite sync :

1 Vpp to 4 Vpp ± 3 dB

All input signals are always 75 ohm terminated, even in the "not selected" mode.

RGB input selection :

Key in the corresponding slot number on the RCU or the local keypad.

Straps on module level :

Floating or non-floating input.

Red :

J3

: strap "yes" : non floating

strap "no" : floating

Green : J4 : strap "yes" : non floating

strap "no" : floating

Blue :

J5 : strap "yes" : non floating

strap "no" : floating

H/C :

J6 : strap "yes" : non floating

strap "no" : floating

V :

J7 : strap "yes" : non floating

strap "no" : floating

Factory preset : strap "yes", non floating input

Sync selection : strap on module level.

J8 : see drawing

Factory preset : separate sync.

Sync selection on the Input Slots menu.

The horizontal sync input can be set as separate sync input or as separate sync + video input. To change this setting, press ENTER key to start up the Adjustment mode..

ANALOG INTERFACE 120 MHz

 

 

ON

INPUT

 

 

 

B

H

V

OFF

 

 

 

R

G

INP

INP

H / C

On

RGB ANALOG INPUT

Vert. sync

Hor. sync or Composite

sync

Blue

Green

Red

J8 Sync selection

Separate sync

Sync on green

J3

J4

J5

J6

J7

Non-Floating

Floating

Floating or non floating input

6-4

 

5975348 BARCOVISION 8200 280497

 

Image 22
Contents Vision Page Barco Projection Systems Date Rev Art. No 280497 R5975348Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service Mode General safety instructions Safety InstructionsInstallation instructions Mains lead AC Power cord with CEE 7 plugFédéral communication commission FCC statement Instructions pour l’installationRemarque sur la Sécurité Prescriptions de securite généralesOn Servicing On InstallationOn Cleaning On RepackingNettoyage ’InstallationEntretien et Réparation Ré-emballageUnpacking Projector dimensionsBarcovision Battery installation in the RCU What about ambient light ? Installation guidelinesEnvironment Which screen type?Definitions of the Abbreviation on drawings Where to install the projector?How to install a projection lens? Inputs and computer video format input compatibilityControl Panel Terminology Location and Functions of ControlFront panel terminology Local keypadTerminology Remote controlRCU Installation SET UP System Settings Connections Power mains cord connectionSwitching on FusesInput connections Switching to stand-by Switching offInput module insertion into the projector Video/S-video input module Straps on module levelRGB analog input module RGB input selectionComponent input selection Component input moduleIndication on the input slot menu RGB3S/RG3sB input module Input selectionSet up of the baud rate for communication with a computer Connecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector OFF OFF OFF On OFF OFF OFF on OFFControlling How to use the RCU?Hardware set up of the projector address Projector addressPicture controls with direct access How to display a projector address?How to program an address into the RCU? How to control the projector or projectorsHow to get source information? How to get a summary of your projector? Software versionInstallation of the settings for a input source Source SET UPInput selection Edit file EnterEdit File Options Rename CopyDelete MoveOptions Source Set Up Video offset Signal operationsGain Still video On/Off Gain adjustment per colorSmoothness Sync Fast/SlowScreen operations Zoom/panMoves the window upwards Picture Compresses the picture in the horizontal direction Conversion ConfigureGeometry Picture Control in Adjustment Mode Start up of the Service mode Service ModeHow to activate the password function? 10-1Convergence adjustment of the LCD panels 0000Green focusing Red on green convergenceBlue on green convergence Reset Lamp Run Time Modify passwordLamp Run Time History 10-6 Barcovision 8200 Standard Source SET UP Files Standard source set up filesStandard Source Set Up Files Battery Replacement in the RCU Battery replacement in the RCULens Cleaning Procedure Focusing the lensLenses Lenses Source Numbers 90 Source numbers 90Insert Card