Barco R9001280 owner manual Controlling, How to use the RCU?, Projector address

Page 27

Controlling

7 CONTROLLING

The projector can be controlled with a. The RCU

b. The hardwired RCU (cable is not included) c. The local keypad.

Controlling the projector with the RCU and the hardwired RCU is equal.

How to use the RCU?

a) Point the front of the RCU to the reflective screen surface.

Ceiling

IR sensor

Screen

c)Point the front of the RCU directly at one of the IR sensors of the projector.

IR sensor

Ceiling

I

0

Table

Front of projector	Rear of projector
IR sensor

9 8

RCU

9	8
	8
3	4

RCU

RCU	When using the wireless remote control, make sure you are within the
	effective operating distance (30m, 100ft in a straight line). The
	remote control unit will not function properly if strong light strikes the
	sensor window or if there are obstacles between the remote control
	unit and the projector IR sensor.

b) RCU used in a hardwired configuration.

0 I

DIAGNOSTICS

IR-ACKNOWLEDGED CODE IR-RECEIVER

RS2 32 O UT

IR-RECEIVED

Projector address

a. hardware set up of the projector address.

Every projector requires an individual address between 0 and 255 which is set with hardware DIP switches. To change that address, it is necessary to first open the top cover (see Gaining access to the DIP switches under Connecting to a computer.).

8 DIP switches (S1) are provided on the CPU module. Each DIP switch has its own decimal value (ON='1', OFF = '0'). The summary of the values associated to those DIP switches gives the address

S1

Projector address

Plug one end of the remote cable in the connector on the bottom of the RCU and the second side in the connector in the front panel of the projector labelled 'REMOTE'.

5975348 BARCOVISION 8200 280497		7-1

Image 27

Contents Vision Page Date Rev Art. No 280497 R5975348 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Service Mode Mains lead AC Power cord with CEE 7 plug Safety InstructionsInstallation instructions General safety instructionsPrescriptions de securite générales Instructions pour l’installationRemarque sur la Sécurité Fédéral communication commission FCC statementOn Repacking On InstallationOn Cleaning On ServicingRé-emballage ’InstallationEntretien et Réparation NettoyageProjector dimensions UnpackingBarcovision Battery installation in the RCU Which screen type? Installation guidelinesEnvironment What about ambient light ?Inputs and computer video format input compatibility Where to install the projector?How to install a projection lens? Definitions of the Abbreviation on drawingsLocal keypad Location and Functions of ControlFront panel terminology Control Panel TerminologyRemote control TerminologyRCU Installation SET UP System Settings Fuses Power mains cord connectionSwitching on ConnectionsSwitching to stand-by Switching off Input connectionsInput module insertion into the projector Straps on module level Video/S-video input moduleRGB input selection RGB analog input moduleComponent input module Component input selectionIndication on the input slot menu Input selection RGB3S/RG3sB input moduleSet up of the baud rate for communication with a computer OFF OFF OFF On OFF OFF OFF on OFF Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector address How to use the RCU?Hardware set up of the projector address ControllingHow to control the projector or projectors How to display a projector address?How to program an address into the RCU? Picture controls with direct accessHow to get source information? Software version How to get a summary of your projector?Source SET UP Installation of the settings for a input sourceInput selection Enter Edit fileEdit File Options Copy RenameMove DeleteOptions Source Set Up Signal operations Video offsetGain Sync Fast/Slow Gain adjustment per colorSmoothness Still video On/OffZoom/pan Screen operationsMoves the window upwards Picture Compresses the picture in the horizontal direction Configure ConversionGeometry Picture Control in Adjustment Mode 10-1 Service ModeHow to activate the password function? Start up of the Service mode0000 Convergence adjustment of the LCD panelsRed on green convergence Green focusingBlue on green convergence Modify password Reset Lamp Run TimeLamp Run Time History 10-6 Barcovision 8200 Standard source set up files Standard Source SET UP FilesStandard Source Set Up Files Battery replacement in the RCU Battery Replacement in the RCUFocusing the lens Lens Cleaning ProcedureLenses Lenses Source numbers 90 Source Numbers 90Insert Card