Barco R9001280 owner manual Source Numbers 90, Source numbers 90

Page 56

Source Numbers 90 - 99

D SOURCE NUMBERS 90 - 99

Source numbers 90 - 99

These source numbers do not correspond to physical inputs. They can only be used when the projector is equipped with a RCVDS 05 or VS05. An additional adjustment file can be created for these source numbers. This file can contain different settings. The relationship between sources 0 - 9 and 90 - 99 is shown in the diagram below.

source input 1

source number 1

file A

source number 91

file A'

 

source input 2

source number 2

file B

source number 92

file B'

 

source input 3

source number 3

file C

source number 93

file C'

 

source input 9

source number 9

file I

source number 99

file I'

 

Follow the steps below to create a second file for sources 0 to 9 :

1.Select the source between 0 and 9.

2.Select the corresponding source number between 90 and 99 with the digit keys on the RCU.

3.Enter the adjustment mode and load a corresponding file. Edit this file if necessary.

4.Save the file and exit the adjustment mode.

5975348 BARCOVISION 8200 210497

 

D-1

 

Image 56
Contents Vision Page Barco Projection Systems Date Rev Art. No 280497 R5975348Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service Mode Safety Instructions Installation instructionsGeneral safety instructions Mains lead AC Power cord with CEE 7 plugInstructions pour l’installation Remarque sur la SécuritéFédéral communication commission FCC statement Prescriptions de securite généralesOn Installation On CleaningOn Servicing On Repacking’Installation Entretien et RéparationNettoyage Ré-emballageBarcovision Projector dimensionsUnpacking Battery installation in the RCU Installation guidelines EnvironmentWhat about ambient light ? Which screen type?Where to install the projector? How to install a projection lens?Definitions of the Abbreviation on drawings Inputs and computer video format input compatibilityLocation and Functions of Control Front panel terminologyControl Panel Terminology Local keypadRCU Remote controlTerminology Installation SET UP System Settings Power mains cord connection Switching onConnections FusesInput module insertion into the projector Switching to stand-by Switching offInput connections Video/S-video input module Straps on module levelRGB analog input module RGB input selectionIndication on the input slot menu Component input moduleComponent input selection RGB3S/RG3sB input module Input selectionSet up of the baud rate for communication with a computer Connecting a Rcvds 05 to the projector Connecting a VS05 to the projectorConnecting an IR Remote Receiver 800 to the projector OFF OFF OFF On OFF OFF OFF on OFFHow to use the RCU? Hardware set up of the projector addressControlling Projector addressHow to display a projector address? How to program an address into the RCU?Picture controls with direct access How to control the projector or projectorsHow to get source information? How to get a summary of your projector? Software versionInput selection Source SET UPInstallation of the settings for a input source Edit file EnterEdit File Options Rename CopyOptions MoveDelete Source Set Up Gain Signal operationsVideo offset Gain adjustment per color SmoothnessStill video On/Off Sync Fast/SlowScreen operations Zoom/panMoves the window upwards Picture Compresses the picture in the horizontal direction Geometry ConfigureConversion Picture Control in Adjustment Mode Service Mode How to activate the password function?Start up of the Service mode 10-1Convergence adjustment of the LCD panels 0000Green focusing Red on green convergenceBlue on green convergence Lamp Run Time History Modify passwordReset Lamp Run Time 10-6 Barcovision 8200 Standard Source SET UP Files Standard source set up filesStandard Source Set Up Files Battery Replacement in the RCU Battery replacement in the RCULenses Focusing the lensLens Cleaning Procedure Lenses Source Numbers 90 Source numbers 90Insert Card