Barco R9001280 owner manual Component input module, Component input selection

Page 23

Connections

Push the control disk key up or down to select System Settings and press ENTER.

Use the control disk to select Input Slots by pushing up or down and press ENTER. The internal system will scan the inputs and displays the result in the Input Slots menu.

Push the control disk up or down to select the corresponding RGB input slot. To change the sync priority for Sync separate, press ENTER key to toggle between CV and CS or HS&VS.

Possible indication :

RGB-SS [CV] = separate sync is composite video signal on H/C input.

RGB-SS [CS or HS&VS] = separate sync is composite sync or horizontal and vertical sync.

RGB-SOG= sync on green.

MAIN MENU

Picture Control

Audio Control

System Settings

File service

SYSTEM SETTINGS

Lamp Control

Installation

•Input slots

Summary

INPUT SLOTS

1. RGB-SS [CV] 2. RGB-SOG

3. Video/S-Video [Video]

•

4. Component video-SS + 800-peripheral

837

Component input module.

Connect your component signals (Y-luma, R-Y and B-Y), e.g. a professional VCR to the Component input module.

Component video : 4 x BNC R-Y : 0.7 Vpp ± 3 dB B-Y : 0.7 Vpp ± 3 dB

Y : 0.7 Vpp ± 3 dB

1 Vpp ± 3 dB if Tri-level sync on green Composite sync : 1 Vpp to 4 Vpp ± 3 dB

All input signals are always 75 ohm terminated, even if the module is "not selected".

On

COMPONENT VIDEO INPUT

Sync

Blue - luma

Luma

Red - luma

GREEN - OPERATION			DIAGNOSTICS
			CODE	IR-RECEIVER
			IR-ACKNOWLEDGED

RS232 OUT		RS 232 IN			REMOTE

IR-RECEIVED

Component input selection :

Key in the corresponding slot number on the RCU or the local keypad.

Indication on the input slot menu :	Professional VCR

Component Video-SS = Component video with separate sync

Component Video-SOY = Component video with sync on Y

Component Video-3LSS = Component video with 3 level separate sync

Component Video-3LSOY = Component video with 3 level sync on Y

5975348 BARCOVISION 8200 280497		6-5

Image 23

Contents Vision Page Date Rev Art. No 280497 R5975348 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Service Mode Mains lead AC Power cord with CEE 7 plug Safety InstructionsInstallation instructions General safety instructionsPrescriptions de securite générales Instructions pour l’installationRemarque sur la Sécurité Fédéral communication commission FCC statementOn Repacking On InstallationOn Cleaning On ServicingRé-emballage ’InstallationEntretien et Réparation NettoyageBarcovision Projector dimensionsUnpacking Battery installation in the RCU Which screen type? Installation guidelinesEnvironment What about ambient light ?Inputs and computer video format input compatibility Where to install the projector?How to install a projection lens? Definitions of the Abbreviation on drawingsLocal keypad Location and Functions of ControlFront panel terminology Control Panel TerminologyRCU Remote controlTerminology Installation SET UP System Settings Fuses Power mains cord connectionSwitching on Connections Input module insertion into the projector Switching to stand-by Switching off Input connections Straps on module level Video/S-video input moduleRGB input selection RGB analog input moduleIndication on the input slot menu Component input moduleComponent input selection Input selection RGB3S/RG3sB input moduleSet up of the baud rate for communication with a computer OFF OFF OFF On OFF OFF OFF on OFF Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector address How to use the RCU?Hardware set up of the projector address ControllingHow to control the projector or projectors How to display a projector address?How to program an address into the RCU? Picture controls with direct accessHow to get source information? Software version How to get a summary of your projector?Input selection Source SET UPInstallation of the settings for a input source Enter Edit fileEdit File Options Copy RenameOptions MoveDelete Source Set Up Gain Signal operationsVideo offset Sync Fast/Slow Gain adjustment per colorSmoothness Still video On/OffZoom/pan Screen operationsMoves the window upwards Picture Compresses the picture in the horizontal direction Geometry ConfigureConversion Picture Control in Adjustment Mode 10-1 Service ModeHow to activate the password function? Start up of the Service mode0000 Convergence adjustment of the LCD panelsRed on green convergence Green focusingBlue on green convergence Lamp Run Time History Modify passwordReset Lamp Run Time 10-6 Barcovision 8200 Standard source set up files Standard Source SET UP FilesStandard Source Set Up Files Battery replacement in the RCU Battery Replacement in the RCULenses Focusing the lensLens Cleaning Procedure Lenses Source numbers 90 Source Numbers 90Insert Card