Barco R9001280 owner manual Connections, Power mains cord connection, Fuses, Switching on

Page 19

Connections

6 CONNECTIONS

Power (mains) cord connection

Use the supplied power cord to connect your projector to the wall outlet. Plug the female power connector into the male connector at the front of the projector.

The power input is auto-ranging from 100 to 240 VAC. This projector may be connected to an IT-power system.

Fuses

Warning

For continued protection against fire hazard :

-refer replacement to qualified service personnel

-ask to replace with the same type of fuse. Fuse type : T12.5 AH/250V

0	I	100 - 230 V
		9	- 4 A
		60 - 50 Hz
			DI AG NOS TI CS
			I R- ACK NO WL EDGE D	CODE	I R- RECE I VE R
RS232 OUT
			I R- RECE I VE D
	0	I
			COMMUNICATION PORT
	RS232 OUT		RS 232 IN	(800-PERIPHERALS)

Switching on

Use the power switch to switch on.

When '0' is visible, the projector is switched off. When '1' is visible, the projector is switched on.

When switching on with the power switch, the projector starts in the stand by mode. The projector mode indication lamp is red.

To start image projection :

a. press the 'Stand by' button on the local keypad or on the remote control. The projector mode indication lamp will be green.

b. press a digit button to select an input source. The projector mode indication lamp will be green.

9	0		EXIT
7	8		ENTER
5	6	TEXT	PAUSE
		TEXT	PAUSE
3	4	SHARPN	BRIGHTN
		SHARPN	BRIGHTN
1	2	PHASE	CONTRAST
		PHASE	CONTRAST

ADJ			EXIT
			ENTER
STBY	PAUSE	TEXT	FREEZ
	HELP	-	+
		PHASE
9	0	-	+
		SHARPNESS
7	8	-	+

Stand by button

0 I	100 - 230 V
	9 - 4 A
	60 - 50 Hz
	DI AGNOSTI CS
	CODE	I R- RECE I VER
	I R- ACK NO WL EDGE D	I R- RECE I VER
RS232 OUT
	I R-RECEI VE D
	Projector mode indication

5975348 BARCOVISION 8200 280497

						TINT

	5		6		-	+
						COLOR

	3		4		-	+
					BRIGHTNESS

	1		2		-	+
						CONTRAST

						6-1

Image 19

Contents Vision Page Date Rev Art. No 280497 R5975348 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Service Mode Mains lead AC Power cord with CEE 7 plug Safety InstructionsInstallation instructions General safety instructionsPrescriptions de securite générales Instructions pour l’installationRemarque sur la Sécurité Fédéral communication commission FCC statementOn Repacking On InstallationOn Cleaning On ServicingRé-emballage ’InstallationEntretien et Réparation NettoyageUnpacking Projector dimensionsBarcovision Battery installation in the RCU Which screen type? Installation guidelinesEnvironment What about ambient light ?Inputs and computer video format input compatibility Where to install the projector?How to install a projection lens? Definitions of the Abbreviation on drawingsLocal keypad Location and Functions of ControlFront panel terminology Control Panel TerminologyTerminology Remote controlRCU Installation SET UP System Settings Fuses Power mains cord connectionSwitching on ConnectionsInput connections Switching to stand-by Switching offInput module insertion into the projector Straps on module level Video/S-video input moduleRGB input selection RGB analog input moduleComponent input selection Component input moduleIndication on the input slot menu Input selection RGB3S/RG3sB input moduleSet up of the baud rate for communication with a computer OFF OFF OFF On OFF OFF OFF on OFF Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Connecting an IR Remote Receiver 800 to the projectorProjector address How to use the RCU?Hardware set up of the projector address ControllingHow to control the projector or projectors How to display a projector address?How to program an address into the RCU? Picture controls with direct accessHow to get source information? Software version How to get a summary of your projector?Installation of the settings for a input source Source SET UPInput selection Enter Edit fileEdit File Options Copy RenameDelete MoveOptions Source Set Up Video offset Signal operationsGain Sync Fast/Slow Gain adjustment per colorSmoothness Still video On/OffZoom/pan Screen operationsMoves the window upwards Picture Compresses the picture in the horizontal direction Conversion ConfigureGeometry Picture Control in Adjustment Mode 10-1 Service ModeHow to activate the password function? Start up of the Service mode0000 Convergence adjustment of the LCD panelsRed on green convergence Green focusingBlue on green convergence Reset Lamp Run Time Modify passwordLamp Run Time History 10-6 Barcovision 8200 Standard source set up files Standard Source SET UP FilesStandard Source Set Up Files Battery replacement in the RCU Battery Replacement in the RCULens Cleaning Procedure Focusing the lensLenses Lenses Source numbers 90 Source Numbers 90Insert Card