Barco R9001280 Gain adjustment per color, Smoothness, Still video On/Off, Sync Fast/Slow

Page 38

Picture Control in Adjustment Mode

Gain adjustment per color

If the obtained color balance is not yet correct, adjust with the separate gain controls until the desired color balance is obtained.

Smoothness

The lower the smoothness value, the sharper the image. The influence of this setting is visible on high density image with small characters.

Still video [On/Off]

This function is only used for stationary interlaced images. Highlight Still Video by pushing the control stick forward or backward and press ENTER to toggle between ON and OFF.

Still Video [On] : the displayed image contains less jitter and gives a sharper image.

Still Video [Off] : for moving pictures.

Sync [Fast/Slow]

Highlight Sync by pushing the control disk up or down and press ENTER to toggle between Slow and Fast.

Note : Sync is normally used in the SLOW position. The FAST position is used to compensate for unsteady sync pulses from older video playback equipment.

Color Balance

Highlight Color Balance by pushing the control disk up or down and press ENTER to select the color balance selection menu.

The next choices are possible : 3200K

6500K

9500K Custom

Use the control disk to make your selection and press ENTER. A marker indicates the actual color balance setting.

When custom is selected, the blue and red color can be adjusted (range from 0 to 2.5) in comparison with the green color (value 1). Push the control disk up or down to select blue or red. Push the control disk to the left or to the right to adjust.

SIGNAL OPERATIONS

Video offset	100
Gain
Gain red	200
Gain green	200
Gain blue	200
Gamma	1.0
Smoothness	4
Still Video	[Off]
Sync	3200
Sync	[Slow]
Color balance	6500

	9500
	Custom
	859
	Tc = custom
	G
R	1.03
B	1.01

9-2		5975348 BARCOVISION 8200 210497

Image 38

Contents Vision Page Barco Projection Systems Date Rev Art. No 280497 R5975348Barco nv/Projection Systems Noordlaan Kuurne BelgiumTable of Contents Service Mode General safety instructions Safety InstructionsInstallation instructions Mains lead AC Power cord with CEE 7 plugFédéral communication commission FCC statement Instructions pour l’installationRemarque sur la Sécurité Prescriptions de securite généralesOn Servicing On InstallationOn Cleaning On RepackingNettoyage ’InstallationEntretien et Réparation Ré-emballageBarcovision Projector dimensionsUnpacking Battery installation in the RCU What about ambient light ? Installation guidelinesEnvironment Which screen type?Definitions of the Abbreviation on drawings Where to install the projector?How to install a projection lens? Inputs and computer video format input compatibilityControl Panel Terminology Location and Functions of ControlFront panel terminology Local keypadRCU Remote controlTerminology Installation SET UP System Settings Connections Power mains cord connectionSwitching on FusesInput module insertion into the projector Switching to stand-by Switching offInput connections Video/S-video input module Straps on module levelRGB analog input module RGB input selectionIndication on the input slot menu Component input moduleComponent input selection RGB3S/RG3sB input module Input selectionSet up of the baud rate for communication with a computer Connecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector OFF OFF OFF On OFF OFF OFF on OFFControlling How to use the RCU?Hardware set up of the projector address Projector addressPicture controls with direct access How to display a projector address?How to program an address into the RCU? How to control the projector or projectorsHow to get source information? How to get a summary of your projector? Software versionInput selection Source SET UPInstallation of the settings for a input source Edit file EnterEdit File Options Rename Copy Options Move Delete Source Set Up Gain Signal operationsVideo offset Still video On/Off Gain adjustment per colorSmoothness Sync Fast/SlowScreen operations Zoom/panMoves the window upwards Picture Compresses the picture in the horizontal direction Geometry ConfigureConversion Picture Control in Adjustment Mode Start up of the Service mode Service ModeHow to activate the password function? 10-1Convergence adjustment of the LCD panels 0000Green focusing Red on green convergenceBlue on green convergence Lamp Run Time History Modify passwordReset Lamp Run Time 10-6 Barcovision 8200 Standard Source SET UP Files Standard source set up filesStandard Source Set Up Files Battery Replacement in the RCU Battery replacement in the RCULenses Focusing the lensLens Cleaning Procedure Lenses Source Numbers 90 Source numbers 90Insert Card