Barco R9001280 owner manual Modify password, Lamp Run Time History, Reset Lamp Run Time

Page 49

Service Mode

Modify password

To change your password, highlight 'Modify password' and press ENTER to start up the password modification procedure.

Enter your old password with the digit keys. After the fourth digit is entered, the next modify password menu is displayed.

Your new password will be asked if your old password is correct. Enter your new password with the digit keys. After the fourth digit, the projector will ask to re-enter your new password.

Re-enter your new password.

When the password is correct, the message "Password modified" will be displayed for a certain time and then the projector returns to the Service menu.

When the password is not correct, an error message "Invalid pass- word" will be displayed. Press EXIT to continue. The projector returns to the Service menu without changing the password.

Lamp Run Time History

To get an overview of the different lamp run times, highlight Lamp Run time History and press ENTER. A listing with the lamp serial number and the corresponding run time will be displayed.

Reset Lamp Run Time.

Highlight Reset Lamp Run Time and press ENTER to select.

5975348 BARCOVISION 8200 210497

MODIFY PASSWORD

Enter Old Password : ----

MODIFY PASSWORD

Enter New Password : ----

MODIFY PASSWORD

Re-enter New Password : ----

SERVICE MODE

 

Modify Password

 

Reset Lamp Run Time

 

Lamp Run Time History

 

Convergence

 

Display Settings

 

Decoder Settings

 

Color

 

I2C

 

LAMP RUN TIME HISTORY

> SN1425634

75 h

SN1234567

1000 h

SN0000000

0 h

SN0000000

0 h

SN0000000

0 h

SN0000000

0 h

SERVICE MODE

Modify Password

Reset Lamp Run Time

Lamp Run Time History

Convergence

Display Settings

Decoder Settings

Color Balance

I2C Device Test

878b

10-5

Image 49
Contents Vision Page Date Rev Art. No 280497 R5975348 Barco Projection SystemsNoordlaan Kuurne Belgium Barco nv/Projection SystemsTable of Contents Service Mode Installation instructions Safety InstructionsGeneral safety instructions Mains lead AC Power cord with CEE 7 plugRemarque sur la Sécurité Instructions pour l’installationFédéral communication commission FCC statement Prescriptions de securite généralesOn Cleaning On InstallationOn Servicing On RepackingEntretien et Réparation ’InstallationNettoyage Ré-emballageUnpacking Projector dimensionsBarcovision Battery installation in the RCU Environment Installation guidelinesWhat about ambient light ? Which screen type?How to install a projection lens? Where to install the projector?Definitions of the Abbreviation on drawings Inputs and computer video format input compatibilityFront panel terminology Location and Functions of ControlControl Panel Terminology Local keypadTerminology Remote controlRCU Installation SET UP System Settings Switching on Power mains cord connectionConnections FusesInput connections Switching to stand-by Switching offInput module insertion into the projector Straps on module level Video/S-video input moduleRGB input selection RGB analog input moduleComponent input selection Component input moduleIndication on the input slot menu Input selection RGB3S/RG3sB input moduleSet up of the baud rate for communication with a computer Connecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector OFF OFF OFF On OFF OFF OFF on OFFHardware set up of the projector address How to use the RCU?Controlling Projector addressHow to program an address into the RCU? How to display a projector address?Picture controls with direct access How to control the projector or projectorsHow to get source information? Software version How to get a summary of your projector?Installation of the settings for a input source Source SET UPInput selection Enter Edit fileEdit File Options Copy RenameDelete MoveOptions Source Set Up Video offset Signal operationsGain Smoothness Gain adjustment per colorStill video On/Off Sync Fast/SlowZoom/pan Screen operationsMoves the window upwards Picture Compresses the picture in the horizontal direction Conversion ConfigureGeometry Picture Control in Adjustment Mode How to activate the password function? Service ModeStart up of the Service mode 10-10000 Convergence adjustment of the LCD panelsRed on green convergence Green focusingBlue on green convergence Reset Lamp Run Time Modify passwordLamp Run Time History 10-6 Barcovision 8200 Standard source set up files Standard Source SET UP FilesStandard Source Set Up Files Battery replacement in the RCU Battery Replacement in the RCULens Cleaning Procedure Focusing the lensLenses Lenses Source numbers 90 Source Numbers 90Insert Card