EverFocus EPTZ 100 manual OSD Menu Setup, Initial Start, 3 RS-485 bus termination

Page 23

3.3.3 RS-485 bus termination

The last device in an RS-485 bus should be terminated by 120Ohm resistor to avoid reflections on the bus (for details, please refer to chapter 3.2.3).

The termination is done by DIP switch DS3.

Termination ON

Termination OFF

3.4INITIAL START

After finishing all installation steps, power on the EPTZ 100.

At power-up, EPTZ 100 will perform an initialization. The communication settings will briefly appear on the screen. Please check these information to ensure the correct DIP switch settings.

Example:

TYPE: EPTZ100

Firmware: 709M/809Q BAUDRATE:9600 RS-485 ID: 1

PROTOCOL: EVERFOCUS

4 OSD MENU SETUP

4.1.1 Operation in Setup Menu

Start EPTZ menu:

Switch between the settings: Enter submenus:

Change the settings:

EXIT OSD menu / submenus:

If DVR Main monitor is selected ("DVR" in LCD display): CAM (hold) + MENU

If no DVR main monitor is selected: MENU or CAM (hold) + MENU or alternatively in both modes:

SHIIFT (hold) + PRESET > 9 5 > ENTER

JOYSTIICK

JOYSTIICK

in CAMERA > ADVANCED SETUP: IIRIIS +

JOYSTIICK

Menu item EXIT/RETURN > JOYSTIICK in CAMERA > ADVANCED SETUP: IIRIIS --

Note: Exceptional commands are described in the OSD.

23	EPTZ100_ma_en_rev03.doc

Image 23

Contents Eptz Weee Safety WarningsTable of Contents Device Setting Camera Delivery Scope FeaturesOptional Accessories IntroductionCommunication SpecificationsAlarm CameraPhysical / environment PowerDimensions with recessed ceiling mount adapter DimensionsDimensions with ceiling mount adapter Dimensions wall bracket Eptz 100 WLM Dimension Eptz 100 with wall mount bracket Eptz 100 WLMDimension ceiling pendant bracket Eptz 100 CPM Dimension Eptz 100 with ceiling pendant bracket Eptz 100 CPMCeiling mount InstallationMechanical Recessed ceiling mount Wall mount Ceiling pendant mount Video PowerElectrical 3 RS-485 3.1 RS-485 installation with EKB 500 keyboard 3.2 RS-485 installation with EverFocus DVR Alarm Baud rate and Protocol Communication Settings2 RS-485 ID address EPTZ100maenrev03.doc 3 RS-485 bus termination OSD Menu SetupOperation in Setup Menu Initial StartOSD Structure Part Menu StructureControl Display Main menuSystem info White BAL Advanced setting camera setupMain Setup CAM Title CameraAuto BacklightMotion DET FocusExposure Brightness Zoom POS InitLens Init ENDSpecial User PresetUart Mode RET PKT Enable ResetScan GROUP2 TiltLevel GROUP1 SpeedPatrol Tour ScanGROUP1 Delete PatternRecord PreviewControl MASK1~4 Privacy MaskInitialize General key description Operation with EKB 500 KeyboardOperation outline EKB 500 Operation with Everfocus Protocol EVF-2Autopan Eptz 100 setup menuPreset positions Pattern tours Preset toursRemote switching of Eptz 100 output relay Switch Alarm Out 1-8 on Switch Alarm Out 1-8 OFFEKB 500 Operation with PELCO-D/P Protocol Group 2 Tour ALL Preset TourPatrol Tour Group 1 TourSwitch relay OFF CLR + F4 1 Enter Switch Alarm Out Switch relay on F4 1 EnterDevice Setting Camera Appendix a Basic Settings AT EKB 500 KeyboardCOM Port Setting RS-485 Interface Setting System I/O Control menu Appendix B Basic Settings AT Everfocus DVREDR / Edvr / Edsr Series Except EDSR100, EDSR100H Ecor / Paragon SeriesGeneral Malfunction Recovering Communication Settings of Camera ModuleChina Subsidiary Japan Subsidiary Head Office USA Subsidiary European Subsidiary