EverFocus EPTZ 100 Special, User Preset, Privacy, Day/Night, Sync, Comm ADJ, Image ADJ, Reset

Page 30

SPECIAL

Submenu for advanced camera functions:

 

USER PRESET

Not supported by EPTZ 100

 

PRIVACY

Keep OFF setting, privacy mask setup is done in the

 

 

PRIVACY MASK menu, available in the main menu

 

DAY/NIGHT

Modes of the day/night switching:

 

 

B/W : black/white (night) mode, IR cut filter switched off

 

 

COLOUR: colour (day) mode, IR cut filter switched on

 

 

AUTO1: day/night switching with short delay time

 

 

AUTO2: day/night switching with longer delay time

 

SYNC:

Synchronization mode, fixed at INTERNAL mode

 

COMM ADJ

Communication settings for camera interface

ATTENTION:

Do not change any value in this submenu!

Keep default settings:

CAM ID

0

DISP CAM ID

OFF

BAUD RATE

38400

UART MODE

8-N-1

RET PKT

ENABLE

If these settings are changed for whatever reason, the communication between dome electronics and camera menu will be broken. In this case consult APPENDIX C for recovering camera module communication settings.

 

IMAGE ADJ

FREEZE: Store ("freeze") current video image

 

 

H-REV: Flips the image horizontally

 

 

V-REV: Flips the image vertically

 

 

SHARPNESS: Image sharpness adjustment in the range

 

 

1 ~ 30

 

 

COLOUR GAIN: Colour saturation adjustment in the

 

 

range 1~ 50

 

END

Return to CAMERA ADVANCED SETTING page

RESET

Reset of the camera parameters to factory defaults.

EXIT

Return to CAMERA menu.

30

EPTZ100_ma_en_rev03.doc

Image 30
Contents Eptz Safety Warnings WeeeTable of Contents Device Setting Camera Introduction FeaturesOptional Accessories Delivery ScopeCamera SpecificationsAlarm CommunicationPower Physical / environmentDimensions Dimensions with ceiling mount adapterDimensions with recessed ceiling mount adapter Dimension Eptz 100 with wall mount bracket Eptz 100 WLM Dimensions wall bracket Eptz 100 WLMDimension Eptz 100 with ceiling pendant bracket Eptz 100 CPM Dimension ceiling pendant bracket Eptz 100 CPMInstallation MechanicalCeiling mount Recessed ceiling mount Wall mount Ceiling pendant mount Power ElectricalVideo 3 RS-485 3.1 RS-485 installation with EKB 500 keyboard 3.2 RS-485 installation with EverFocus DVR Alarm Communication Settings Baud rate and Protocol2 RS-485 ID address EPTZ100maenrev03.doc Initial Start OSD Menu SetupOperation in Setup Menu 3 RS-485 bus terminationMenu Structure OSD Structure PartControl Main menu System infoDisplay Camera Advanced setting camera setupMain Setup CAM Title White BALFocus BacklightMotion DET AutoEND Zoom POS InitLens Init Exposure BrightnessReset User PresetUart Mode RET PKT Enable SpecialScan GROUP1 Speed TiltLevel GROUP2Tour Scan GROUP1Patrol Preview PatternRecord DeleteControl Privacy Mask MASK1~4Initialize Operation with EKB 500 Keyboard General key descriptionEKB 500 Operation with Everfocus Protocol EVF-2 Operation outlineEptz 100 setup menu Preset positionsAutopan Switch Alarm Out 1-8 on Switch Alarm Out 1-8 OFF Preset toursRemote switching of Eptz 100 output relay Pattern toursEKB 500 Operation with PELCO-D/P Protocol Group 1 Tour ALL Preset TourPatrol Tour Group 2 TourSwitch relay on F4 1 Enter Switch relay OFF CLR + F4 1 Enter Switch Alarm OutAppendix a Basic Settings AT EKB 500 Keyboard COM Port Setting RS-485 Interface SettingDevice Setting Camera Ecor / Paragon Series Appendix B Basic Settings AT Everfocus DVREDR / Edvr / Edsr Series Except EDSR100, EDSR100H System I/O Control menuRecovering Communication Settings of Camera Module General MalfunctionHead Office USA Subsidiary European Subsidiary China Subsidiary Japan Subsidiary