EverFocus EPTZ 100 manual EKB 500 Operation with PELCO-D/P Protocol

Page 42

5.2EKB 500 OPERATION WITH PELCO-D/P PROTOCOL

NOTE: Not all EPTZ 100 functions are available in PELCO-D/P protocol. Operation for ssome functions is different to operation with EVERFOCUS protocol.

5.2.1 EPTZ 100 setup menu

Start EPTZ 100 menu:

Switch between the settings:

Enter submenus:

Change the settings:

EXIT OSD menu / submenus:

If DVR Main monitor is selected ("DVR" in LCD display):

CAM (hold) + MENU

If no DVR main monitor is selected: MENU or CAM (hold) + MENU or alternatively in both modes:

SHIIFT (hold) + PRESET > 9 5 > ENTER

JOYSTIICK

JOYSTIICK

in CAMERA ADVANCED SETUP: IIRIIS +

JOYSTIICK

Menu item EXIT/RETURN > JOYSTIICK in CAMERA ADVANCED SETUP: IIRIIS --

Note: Exceptional commands are described in the OSD.

5.2.2 Preset positions

Up to 64 preset PTZ positions can be stored in EPTZ 100.

Save presets

SHIIFT (hold) + POSIITIION > [ preset number ] > ENTER

Delete preset

CLR (hold) + POSIITIION

> [ preset number ] > ENTER

Start (go to) preset

POSIITIION > [ preset number ] > ENTER

Camera:0001 Save to Position:___[1-192]

Camera:0001

Del Position:___

Camera:0001 go to Position:___[1-192]

42

EPTZ100_ma_en_rev03.doc

Image 42
Contents Eptz Safety Warnings WeeeTable of Contents Device Setting Camera Introduction FeaturesOptional Accessories Delivery ScopeCamera SpecificationsAlarm CommunicationPower Physical / environmentDimensions Dimensions with ceiling mount adapterDimensions with recessed ceiling mount adapter Dimension Eptz 100 with wall mount bracket Eptz 100 WLM Dimensions wall bracket Eptz 100 WLMDimension Eptz 100 with ceiling pendant bracket Eptz 100 CPM Dimension ceiling pendant bracket Eptz 100 CPMInstallation MechanicalCeiling mount Recessed ceiling mount Wall mount Ceiling pendant mount Power ElectricalVideo 3 RS-485 3.1 RS-485 installation with EKB 500 keyboard 3.2 RS-485 installation with EverFocus DVR Alarm Communication Settings Baud rate and Protocol2 RS-485 ID address EPTZ100maenrev03.doc Initial Start OSD Menu SetupOperation in Setup Menu 3 RS-485 bus terminationMenu Structure OSD Structure PartControl Main menu System infoDisplay Camera Advanced setting camera setupMain Setup CAM Title White BALFocus BacklightMotion DET AutoEND Zoom POS InitLens Init Exposure BrightnessReset User PresetUart Mode RET PKT Enable SpecialScan GROUP1 Speed TiltLevel GROUP2Tour Scan GROUP1Patrol Preview PatternRecord DeleteControl Privacy Mask MASK1~4Initialize Operation with EKB 500 Keyboard General key descriptionEKB 500 Operation with Everfocus Protocol EVF-2 Operation outlineEptz 100 setup menu Preset positionsAutopan Switch Alarm Out 1-8 on Switch Alarm Out 1-8 OFF Preset toursRemote switching of Eptz 100 output relay Pattern toursEKB 500 Operation with PELCO-D/P Protocol Group 1 Tour ALL Preset TourPatrol Tour Group 2 TourSwitch relay on F4 1 Enter Switch relay OFF CLR + F4 1 Enter Switch Alarm OutAppendix a Basic Settings AT EKB 500 Keyboard COM Port Setting RS-485 Interface SettingDevice Setting Camera Ecor / Paragon Series Appendix B Basic Settings AT Everfocus DVREDR / Edvr / Edsr Series Except EDSR100, EDSR100H System I/O Control menuRecovering Communication Settings of Camera Module General MalfunctionHead Office USA Subsidiary European Subsidiary China Subsidiary Japan Subsidiary