EverFocus EPTZ 100 manual Eptz 100 setup menu, Preset positions, Autopan

Page 40

5.1.1 EPTZ 100 setup menu

Start EPTZ menu:

If DVR Main monitor is selected ("DVR" in LCD display):

 

CAM (hold) + MENU

 

If no DVR main monitor is selected:

 

MENU or CAM (hold) + MENU

 

or alternatively in both modes:

 

SHIIFT (hold) + PRESET > 9 5 > ENTER

Switch between the settings:

JOYSTIICK

Enter submenus:

JOYSTIICK

 

in CAMERA > ADVANCED SETUP: IIRIIS +

Change the settings:

JOYSTIICK

EXIT OSD menu / submenus:

Menu item EXIT/RETURN > JOYSTIICK

 

in CAMERA > ADVANCED SETUP: IIRIIS --

Note: Exceptional commands are described in the OSD.

5.1.2 Preset positions

Up to 64 preset PTZ positions can be stored in EPTZ 100.

Save presets

SHIIFT (hold) + POSIITIION > [ preset number ] > ENTER

Delete preset

CLR (hold) + POSIITIION

> [ preset number ] > ENTER

Start (go to) preset

POSIITIION > [ preset number ] > ENTER

Camera:0001 Save to Position:___[1-192]

Camera:0001

Del Position:___

Camera:0001 go to Position:___[1-192]

5.1.3 Autopan

The speed for autopan function is programmed in OSD menu; the entered value for speed in EKB 500 will

be ignored at start of autopan.

Activate A-B autopan (pan between 2 points)

A..PAN > any value 1~ 239 > ENTER

Activate 360° autopan

SHIIFT (hold) + A..PAN > any value 1~ 239 > ENTER

Speed:___[1-239] [ENT] to start.

40

EPTZ100_ma_en_rev03.doc

Image 40
Contents Eptz Safety Warnings WeeeTable of Contents Device Setting Camera Features Optional AccessoriesIntroduction Delivery ScopeSpecifications AlarmCamera CommunicationPower Physical / environmentDimensions with ceiling mount adapter DimensionsDimensions with recessed ceiling mount adapter Dimension Eptz 100 with wall mount bracket Eptz 100 WLM Dimensions wall bracket Eptz 100 WLMDimension Eptz 100 with ceiling pendant bracket Eptz 100 CPM Dimension ceiling pendant bracket Eptz 100 CPMMechanical InstallationCeiling mount Recessed ceiling mount Wall mount Ceiling pendant mount Electrical PowerVideo 3 RS-485 3.1 RS-485 installation with EKB 500 keyboard 3.2 RS-485 installation with EverFocus DVR Alarm Communication Settings Baud rate and Protocol2 RS-485 ID address EPTZ100maenrev03.doc OSD Menu Setup Operation in Setup MenuInitial Start 3 RS-485 bus terminationMenu Structure OSD Structure PartControl System info Main menuDisplay Advanced setting camera setup Main Setup CAM TitleCamera White BALBacklight Motion DETFocus AutoZoom POS Init Lens InitEND Exposure BrightnessUser Preset Uart Mode RET PKT EnableReset SpecialScan Tilt LevelGROUP1 Speed GROUP2GROUP1 Tour ScanPatrol Pattern RecordPreview DeleteControl Privacy Mask MASK1~4Initialize Operation with EKB 500 Keyboard General key descriptionEKB 500 Operation with Everfocus Protocol EVF-2 Operation outlinePreset positions Eptz 100 setup menuAutopan Preset tours Remote switching of Eptz 100 output relaySwitch Alarm Out 1-8 on Switch Alarm Out 1-8 OFF Pattern toursEKB 500 Operation with PELCO-D/P Protocol ALL Preset Tour Patrol TourGroup 1 Tour Group 2 TourSwitch relay on F4 1 Enter Switch relay OFF CLR + F4 1 Enter Switch Alarm OutCOM Port Setting RS-485 Interface Setting Appendix a Basic Settings AT EKB 500 KeyboardDevice Setting Camera Appendix B Basic Settings AT Everfocus DVR EDR / Edvr / Edsr Series Except EDSR100, EDSR100HEcor / Paragon Series System I/O Control menuRecovering Communication Settings of Camera Module General MalfunctionHead Office USA Subsidiary European Subsidiary China Subsidiary Japan Subsidiary