EverFocus EPTZ 100 manual Main menu, System info, Display

Page 26

4.1.3 Main menu

After opening OSD setup the MAIN menu is shown at the screen:

MAIN MENU

SYSTEM INFO

DISPLAY

CAMERA

SCAN

CONTROL

PRIVACY MASK

ALARM

INITIALIZE

EXIT

Select a menu item with UP/DOWN, RIGHT will open submenu.

NOTE: The OSD menu has a timeout function. After 2 minutes with no activity, the OSD menu will close automatically.

4.1.4 System info

This menu shows the camera type, firmware version and communication settings. There are no editable items in this menu.

SYSTEM INFO	EPTZ100
TYPE	EPTZ100
FIRMWARE	709M809Q
BAUD RATE	9600
RS-485 ID	1
PROTOCOL	EVERFOCUS

4.1.5 Display

The settings in this menu define the overlay displays of the camera.

CAMERA ID	Shows the RS-485 ID on the screen:
	ON: display of RS-485 ID
	OFF: no display of RS-485 ID
CAMERA NAME	With setting ON, a camera title with up to 16 characters can be entered.
	ON: display of camera title (with option for edit)
	OFF: no title display
PRESET NUMBER	ON: display number of active preset
	OFF: no preset number display
PRESET NAME	ON: display of a freely editable title (up to 16 characters) of the preset
	(available for presets 1 ~ 32)
	OFF: no display of preset name
PTZ POSITION	ON: show coordinates for pan and tilt in degrees and zoom ratio
	OFF: no PTZ position display
RETURN	Returns to main menu

26	EPTZ100_ma_en_rev03.doc

Image 26

Contents Eptz Safety Warnings WeeeTable of Contents Device Setting Camera Introduction FeaturesOptional Accessories Delivery ScopeCamera SpecificationsAlarm CommunicationPower Physical / environmentDimensions with recessed ceiling mount adapter DimensionsDimensions with ceiling mount adapter Dimension Eptz 100 with wall mount bracket Eptz 100 WLM Dimensions wall bracket Eptz 100 WLMDimension Eptz 100 with ceiling pendant bracket Eptz 100 CPM Dimension ceiling pendant bracket Eptz 100 CPMCeiling mount InstallationMechanical Recessed ceiling mount Wall mount Ceiling pendant mount Video PowerElectrical 3 RS-485 3.1 RS-485 installation with EKB 500 keyboard 3.2 RS-485 installation with EverFocus DVR Alarm Communication Settings Baud rate and Protocol2 RS-485 ID address EPTZ100maenrev03.doc Initial Start OSD Menu SetupOperation in Setup Menu 3 RS-485 bus terminationMenu Structure OSD Structure PartControl Display Main menuSystem info Camera Advanced setting camera setupMain Setup CAM Title White BALFocus BacklightMotion DET AutoEND Zoom POS InitLens Init Exposure BrightnessReset User PresetUart Mode RET PKT Enable SpecialScan GROUP1 Speed TiltLevel GROUP2Patrol Tour ScanGROUP1 Preview PatternRecord DeleteControl Privacy Mask MASK1~4Initialize Operation with EKB 500 Keyboard General key descriptionEKB 500 Operation with Everfocus Protocol EVF-2 Operation outlineAutopan Eptz 100 setup menuPreset positions Switch Alarm Out 1-8 on Switch Alarm Out 1-8 OFF Preset toursRemote switching of Eptz 100 output relay Pattern toursEKB 500 Operation with PELCO-D/P Protocol Group 1 Tour ALL Preset TourPatrol Tour Group 2 TourSwitch relay on F4 1 Enter Switch relay OFF CLR + F4 1 Enter Switch Alarm OutDevice Setting Camera Appendix a Basic Settings AT EKB 500 KeyboardCOM Port Setting RS-485 Interface Setting Ecor / Paragon Series Appendix B Basic Settings AT Everfocus DVREDR / Edvr / Edsr Series Except EDSR100, EDSR100H System I/O Control menuRecovering Communication Settings of Camera Module General MalfunctionHead Office USA Subsidiary European Subsidiary China Subsidiary Japan Subsidiary