Toshiba IK-WB21A manual Camera/E-mail Settings, Click 5. E-mail in the sub menu, Off

Page 38

Camera/Alarm Settings (Cont.)

 

●

Alarm In/Ext. Control In

Introduction

1)

Set an "alarm" to be detected.

 

Alarm In:

Detects an external alarm.

 

 

 

 

Ext. Control In: Performs external control.

 

 

OFF:

Does not perform "Alarm In" or "Ext. Control In."

 

2)

Set "Input type" for alarms if "Function" is set to other than "OFF."

 

 

Normally Opened (NO): A no-voltage contact system. Set in case of

 

 

 

 

normally open, closed in case of an alarm.

Viewing and

 

Normally Closed (NC): A no-voltage contact system. Set in case of

 

 

 

normally closed, open in case of an alarm.

 

 

 

 

Listening Operation

NOTE

 

 

 

 

 

 

 

 

・

●

Camera starts alarm recording when camera detects alarm signal. (Signal

 

lenghth requires more than 100ms).

● Camera starts "Ext. Control In Recording" when control signal comes in. (Control signal should be more than 1 second).

●Motion Detection

1) Function

Recording

 

ON: Camera detects motion. (A change in the screen is detected and

 

an alarm is sent)

 

 

 

 

OFF: Camera does not detect motion.

 

2)

Sensitivity

 

 

Set "Sensitivity."

 

 

HIGH:

It works with even a small change in brightness or motion is

 

 

 

 

detected.

 

 

MIDDLE: Intermediate between HIGH and LOW.

 

 

LOW:

It works only when a large change in brightness or motion is

Set

 

 

 

detected.

NOTE

 

 

up

 

 

●

Detection sometimes fails if the object is dark.

 

 

●

Incorrect detection is sometimes made due to noise if the object is dark and

 

 

AGC gain is high. Set the sensitivity to low.

 

●

Output Hold Time

Others

 

Set a time to hold alarm output.

 

Choose from 1, 5, 10, 15, 30 and 60 seconds

 

 

This function is used when connecting to alarm output terminals and activating a siren, buzzer or emergency light.

Camera/E-mail Settings

E-mail can be sent to a maximum of 11 destinations including the administrator e-mail address in case of Alarm In or Motion Detection.

1 Click "Camera Settings" on the Admin. Menu.

･A sub menu for Camera Settings will appear.

2 Click "5. E-mail" in the sub menu.

･The screen of "Camera - E-mail Settings" Settings will appear.

3 Configure each setting items.

･Click the Save button to save settings.

･The settings will not be reflected unless the Save button is clicked.

Introduction

and

Viewing

Operation

Listening

 

・

Recording

Set up

Others

74

75

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Model IK-WB21A Fccus Information Tested To Comply With FCC Standards IntroductionTerms and Trademarks For Home or Office USETable of Contents Recording Images on FTP Server ･ Recording by alarmSetting ･ Scheduled RecordingImportant Safeguards Important Safeguards AC adaptor Precautions for UseSpecifications SD Memory CardFeatures of the Camera Overview of the Network CameraRemove the terminal cover Installing the CameraNames of Camera Parts Connect the AC adapter cable and LAN cable to the cameraWhen installing on ceiling AC adapter cable LAN cableRemoving the camera from the ceiling attachment Install the cover for mounting on a ceilingMount the camera on the ceiling attachment Connecting the Power Cord Turning on the PowerItems needed for network camera monitoring system IP AddressSet the IP address of the personal computer Connection ConfigurationTest the camera connection using ping Click the camera you want to login from the list of cameras Click the Administrator button or the User buttonAdministrator Log-in and User Log-in OperationSetup Screen Administrator Log-in Screen and User Log-in ScreenViewing images Browser setting when proxy server is usedViewing and listening Log-in the cameraMoving the screen center AudioCamera image screen Number and Item DescriptionPreset button. The preset control panel will ControllerPresetting of Camera Position by Administrator Assign the camera position in the Preset list Selecting a PresetConfiguring a Preset Preset Position Settings Setup Preset ItemsPreset Name Settings Playing Recorded Alarm Images Playing Recorded Normal ImagesClick Audio in the sub menu Click Camera Settings on the Admin. menu. ThenAudio Out Camera Image screen and set to displayAbout Recording Images Record setting Insert SD memory card to the cameraClick Camera Settings on the Admin. Menu Click Recording in the sub menuClick the Save button under the items Configure each setting itemsClick Camera Settings in the Admin. Menu Deleting Record FileRecording Images on FTP Server Record settingClick the Save button to save settings Click FTP Recording in the sub menuScheduled Recording Transfer Image SizeFTP Server Usage Displayed if Scheduled Recording is chosen as an FTPEX/MD SD card back up Images Jpeg files can be recorded in a personal computer ･ The setup screen for Jpeg Local Saving will appearFile Transfer Order Scheduled Recording ･ Jpeg file will appear on the personal computerClick an item in the sub menu desired to set Setting･ The setup screen for Wave Local Saving will appear Sound can be recorded in a personal computer wav fileCamera/Basic Settings Click 1. General in the sub menuOperating color Overview Characteristics Remarks CameraTemperature AutomaticallyHigh LOWMiddle Setup 3 Item setting Camera/Alarm SettingsClick Camera Settings on the Administrator Setup MenuOFF Camera/E-mail SettingsClick 5. E-mail in the sub menu Operation Introduction Camera/Audio Settings Click 6. Audio in the sub menuPAN/TILT Basic Settings Click PAN/TILT Settings in the Admin. Menu･ a setup screen of PAN/TILT Preset Settings will appear PAN/TILT Preset SettingsClick 2. Preset in the sub menu PAN/TILT Operation Range Click PAN/TILT Settings in the Administrator Setup menuPAN/TILT Auto Patrol Click 3. Auto Patrol in the sub menu･ The sub menu for Network Settings will appear Network Basic SettingsClick Network Settings in the Admin. Menu ･ a setup screen of Network Basic Settings will appearClick 2. Ddns in the sub menu Network/DDNS SettingsNetwork / FTP Server Settings Click 3. FTP Server in the sub menuClick 1. Adding and Removing Cameras in the sub menu Click Multi Screen Display in the Admin. Menu･ The sub menu for multi screen display setting will appear Administrator log-in name and password can be set Click Admin. Function in the Admin. MenuClick 1. Changing ID/Password in the sub menu ･ The sub menu for administrator functions will appearClick 2. User Operation Restriction in the sub menu Click Admin. Functions in the Admin. Menu･ The sub menu for administrator function will appear Click 3. Date and Time in the sub menuSelect the file for the latest firmware saved in First step Click 4. FW Update in the sub menuClick the Browse... button Click the Upload button in the screen for StepReset all set values to factory defaults Click Configuration Information in the sub menuSelect a saved setup file Network Camera RebootingLooking up the log or setup items Alarm TerminalsClick Log Management in the Admin. Menu Click 1. Browse and Delete in the sub menuExample Circuit Connection Specifications of Alarm SignalsGlossary Index Jpeg LANFTP LiveLog Display Output message Message109 Before Calling Service Personnel Before Calling Service Personnel... 114 116 117 Specifications OthersAppearance Diagram Installed on desk Unit mm inches Installed on ceilingPreamble GNU General Public LicenseVersion 2, June 125 No Warranty END of Terms and ConditionsToshiba America Information SYSTEMS. INC
Top Page Image Contents