Toshiba IK-WB21A manual Camera/Audio Settings, Click 6. Audio in the sub menu

Page 40

and Operation

Introduction

Viewing ・ Listening

Recording

Set up

Others

Camera/E-mail Settings (Cont.)

● E-mail Address List

1)Set ON or OFF in "Always Sent to Administrator E-mail Address." ON: Always send to administrator E-mail address.

OFF: Not send to administrator E-mail address.

2)Enter "Mail-to Address." (Up to ten addresses)

3)Check send conditions.

Alarm In:

E-mail is sent to checked addresses when camera

 

detect alarms.

Motion Detection: E-mail is sent to checked addresses when camera motion is detected.

NOTE

●POP is a protocol for receiving e-mail from e-mail box. As the network camera does not receive e-mail, e-mail in POP server will not be lost due to this setting.

●The e-mail function of the network camera is not compatible to "SMTP Auth."

●The frame rate deteriorates if resolution of "Attached Image Size" differs from "Resolution" in "1. General" of "Camera Settings".

●When wishing to send e-mail to administrator's address only in case of either "Alarm In" or "Motion Detectoin", set to "OFF" in "Always Send to Administrator E-mail Address", add the Administrator E-mail address to "Mail-to Address" and check one of "Send Conditoins."

Camera/Audio Settings

Set audio input to and output from the network camera.

1 Click "Camera Settings" on the Admin. Menu.

･A sub menu for Camera Settings will appear.

2 Click "6. Audio" in the sub menu.

･The screen of "Camera - Audio" will appear.

3 Configure each setting items.

･Click the Save button to save settings.

･The settings will not be reflected unless the Save button is clicked.

●Audio Input Set audio input.

ON: The camera receives audio.

OFF: The camera does not recieve audio.

･Set to "ON" when inputting audio from a microphone connected to the camera.

●Audio Input Level

An audio input level is set.

HIGH:

Increases the audio input level.

MIDDLE:

Adjusts the audio input level to a medium level.

LOW:

Reduces the audio input level.

●Audio Output Set audio output.

ON: The camera receives audio.

OFF: The camera does not recieve audio.

･Set to "ON" when outputting audio from a microphone connected to the camera.

●Audio Output Level

An audio output level is set.

HIGH:

Increases the audio output level.

MIDDLE:

Adjusts the audio output level to a medium level.

LOW:

Reduces the audio output level.

Introduction

and

Viewing

Operation

Listening

 

・

Recording

Set up

Others

78

79

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Model IK-WB21A Introduction Terms and TrademarksFccus Information Tested To Comply With FCC Standards For Home or Office USETable of Contents ･ Recording by alarm SettingRecording Images on FTP Server ･ Scheduled RecordingImportant Safeguards Important Safeguards Precautions for Use SpecificationsAC adaptor SD Memory CardFeatures of the Camera Overview of the Network CameraInstalling the Camera Names of Camera PartsRemove the terminal cover Connect the AC adapter cable and LAN cable to the cameraWhen installing on ceiling AC adapter cable LAN cableMount the camera on the ceiling attachment Install the cover for mounting on a ceilingRemoving the camera from the ceiling attachment Connecting the Power Cord Turning on the PowerItems needed for network camera monitoring system IP AddressTest the camera connection using ping Connection ConfigurationSet the IP address of the personal computer Click the camera you want to login from the list of cameras Click the Administrator button or the User buttonAdministrator Log-in and User Log-in OperationSetup Screen Administrator Log-in Screen and User Log-in ScreenBrowser setting when proxy server is used Viewing and listeningViewing images Log-in the cameraAudio Camera image screenMoving the screen center Number and Item DescriptionPreset button. The preset control panel will ControllerPresetting of Camera Position by Administrator Configuring a Preset Selecting a PresetAssign the camera position in the Preset list Preset Name Settings Setup Preset ItemsPreset Position Settings Playing Recorded Alarm Images Playing Recorded Normal ImagesClick Camera Settings on the Admin. menu. Then Audio OutClick Audio in the sub menu Camera Image screen and set to displayRecord setting Insert SD memory card to the camera Click Camera Settings on the Admin. MenuAbout Recording Images Click Recording in the sub menuConfigure each setting items Click Camera Settings in the Admin. MenuClick the Save button under the items Deleting Record FileRecord setting Click the Save button to save settingsRecording Images on FTP Server Click FTP Recording in the sub menuTransfer Image Size FTP Server UsageScheduled Recording Displayed if Scheduled Recording is chosen as an FTPEX/MD SD card back up ･ The setup screen for Jpeg Local Saving will appear File Transfer Order Scheduled RecordingImages Jpeg files can be recorded in a personal computer ･ Jpeg file will appear on the personal computerSetting ･ The setup screen for Wave Local Saving will appearClick an item in the sub menu desired to set Sound can be recorded in a personal computer wav fileCamera/Basic Settings Click 1. General in the sub menuOverview Characteristics Remarks Camera TemperatureOperating color AutomaticallyMiddle LOWHigh Camera/Alarm Settings Click Camera Settings on the Administrator SetupSetup 3 Item setting MenuClick 5. E-mail in the sub menu Camera/E-mail SettingsOFF Operation Introduction Camera/Audio Settings Click 6. Audio in the sub menuPAN/TILT Basic Settings Click PAN/TILT Settings in the Admin. MenuClick 2. Preset in the sub menu PAN/TILT Preset Settings･ a setup screen of PAN/TILT Preset Settings will appear Click PAN/TILT Settings in the Administrator Setup menu PAN/TILT Auto PatrolPAN/TILT Operation Range Click 3. Auto Patrol in the sub menuNetwork Basic Settings Click Network Settings in the Admin. Menu･ The sub menu for Network Settings will appear ･ a setup screen of Network Basic Settings will appearNetwork/DDNS Settings Network / FTP Server SettingsClick 2. Ddns in the sub menu Click 3. FTP Server in the sub menu･ The sub menu for multi screen display setting will appear Click Multi Screen Display in the Admin. MenuClick 1. Adding and Removing Cameras in the sub menu Click Admin. Function in the Admin. Menu Click 1. Changing ID/Password in the sub menuAdministrator log-in name and password can be set ･ The sub menu for administrator functions will appearClick Admin. Functions in the Admin. Menu ･ The sub menu for administrator function will appearClick 2. User Operation Restriction in the sub menu Click 3. Date and Time in the sub menuClick 4. FW Update in the sub menu Click the Browse... buttonSelect the file for the latest firmware saved in First step Click the Upload button in the screen for StepClick Configuration Information in the sub menu Select a saved setup fileReset all set values to factory defaults Network Camera RebootingAlarm Terminals Click Log Management in the Admin. MenuLooking up the log or setup items Click 1. Browse and Delete in the sub menuGlossary Index Specifications of Alarm SignalsExample Circuit Connection LAN FTPJpeg LiveLog Display Output message Message109 Before Calling Service Personnel Before Calling Service Personnel... 114 116 117 Specifications OthersAppearance Diagram Installed on desk Unit mm inches Installed on ceilingVersion 2, June GNU General Public LicensePreamble 125 No Warranty END of Terms and ConditionsToshiba America Information SYSTEMS. INC
Top Page Image Contents