JVC VN-C205 manual Connect the LAN cable, Point the camera in the direction you wish to capture

Page 11

Preparation (Step 1 Connection/Installation)

1-2 Mounting the Camera to the Ceiling (Continued)

2.Installation

1. Attach to ceiling slab

 

Alarm signal cable

Video signal

5.

Solder or

cable

crimp

 

 

Safety

 

Insulation tape

cable

 

2 .

Input power supply

cable

 

LAN cable

4 .

Alarm Signal Cable

3 .

10 BASE -T/100 BASE-TX

 

Terminal

 

LAN cable

1.Attach the safety cable to the ceiling slab. (Safety cable not included)

Attach the safety cable that has already been attached to the camera to the ceiling slab or channel. Make sure that the wire is attached securely.

2.Connect the video signal cable. Connect the coaxial cables (BNC) to the video signal output connector (BNC).

Cable

Maximum length (No

cable compensator)

 

RG-59

200m

(650 ft)

RG-6

350m

(1140 ft)

RG-11

450m

(1470 ft)

3.Connect the LAN cable

Pass the LAN cable coming out from the ceiling under the plate for depressing cables, connect it to the 10BASE-T/100BASE-TX Terminal of the camera unit.

Caution

The use of a crossover cable may not be supported by certain LAN boards on some rare occasions. As such, please check your LAN board specifications before connection.

6.

Wrap with tape

BNC Connector

Input power cable connection

Wrap with tape

LAN cable

Alarm signal cable

6.Wrap insulation tape around cables. As shown in the diagram to the left, wrap insulation tape around the input power cable connection and BNC connector. Insert the cables into the hole in the ceiling.

Note

Wrapping the wires with insulation tape improves handling as well as reducing interference.

7.Point the camera in the direction you wish to capture.

Point the camera so that the Horizontal Lock screw is facing the direction you wish to capture. The camera can be adjusted ±60˚ horizontally to either side of the Horizontal Lock screw.

8.Mount the camera to the ceiling.

Use M4-sized (No. 8) screws/bolts or wood screws (￿4.1mm, 1/8 inches) to secure the camera in four places when mounting to the ceiling or wall.

Caution

Note

When using 100 BASE-TX, ensure to use a Category 5 (or higher) cable.

4. Connect the alarm terminal

Connect the alarm cable wired in step 5 of

Preparations (page 17) to the alarm

terminal of camera unit. Pass the cable under

7.

Horizontal Lock screw

Mounting

Mounting holes

Tighten all screws securely. Otherwise the camera may come loose and fall.

the plate for depressing cables same as step

3 before connecting.

5. Connect the input power supply cable.

Connect the cable protruding from the ceiling

to the input power cable. (Page 22)

Note

The input power cable uses materials similar to those of machinery wiring, so wrap the cable with insulation tape to prevent it from becoming damaged when mounting the camera.

Use durable wiring for the input power cable.

holes

8.

Screws

20

 

 

 

21

Image 11
Contents VN-C205 VN-C205INSTRUCTIONSInformation for USA Not apply to all appliancesOperation SettingsContents Introduction Preparation SettingsIntroduction CharacteristicsOperating Precautions Operating Environment Name and Function of Parts Latest UpdatesVideo setting switch Connection Examples Preparation ProcedurePreparation Flowchart of installation work for camera Getting StartedInstallation Adjustment of the camera’s angle of viewPreparations Preparation Connection/InstallationMounting the Camera to the Ceiling  Inserting the CF card Preparations  Connection to Alarm Input/Output TerminalPoint the camera in the direction you wish to capture Connect the alarm terminalConnect the input power supply cable Connect the LAN cableAdjusting the iris level Settings related to video When installing the Camera to the electrical boxAdjusting the focal length Adjusting the focusWhite-spot correction Installing the SoftwarePull out the cables aside and mount Select Internet Protocol TCP/IP and click Properties Setting PCs IP Address Windows XPSettings Network Settings ClickSet IP address to Setting PCs IP Address WindowsFor Windows 2000, set according to the following procedure Select Settings and click PropertiesClick Start up the V.Networks Controller. This VN-C205U Setup Tool only allows connection of VN-C205Check settings For other settings, nextViewing of motion images only Other Settings Using the VN-C205U Setup ToolAuthorization Level Allowed Access All operations using the V.Networks ControllerOther Settings Using the VN-C205U Setup Tool 2. Multicast Perform area setting Operation when an alarm input is activated This section describes procedures for alarm settingAlarm Input Alarm FTP Alarm 1/AlarmDetect Mode Alarm OutputOutput Value  Alarm Output Function/Set ValueOutput Output Set ValuesRecording files Setting the Advance screenRecording time Displaying still images uploaded to the /user folder Other Settings Using the VN-C205U Setup Tool 6. WebOther Settings Using the VN-C205U Setup Tool 7. FTP Server Start up the VN-C205U Setup Tool and select FTP ServerAlarm FTP Upload Setting PasswordError recovery Connection error Transfer errorStart up the VN-C205U Setup Tool and select Memory Info Start up the VN-C205U Setup Tool and select TimeWhen NTP is used Connect to VN-C205 NormalHigh Speed Starting Up V.Networks Controller Features that Allow Setting Using the V.Networks ControllerImage Size and Inversion Settings Setting Using the V.Networks ControllerSelect View Specify Image Size and Upside Down settings Motion Detection StandbyFrame Rate Image Quality SettingOperations Setting Using the V.Networks Controller Alarm Setting Time Stamp Select Setting and Time Stamp Perform settingSelect Setting and Property Perform setting When alteration is complete, clickRecord/Stop Click Playback screen is displayed Operations Operation Using the V.Networks ControllerPlayback Play buttonSnapshot Operating Environment Access Authorization LevelStarting Up the Web Browser Setting Using the Web BrowserOperations Operating Using a Web Browser Setting Using the Web Browser 1. Other Settings Setting Using the Web Browser 2. View Setting  Alarm Out Setting Using the Web Browser 3. Alarm SettingClick to apply settings and to save the set values  AlarmOperations Setting Using the Web Browser Setting Using the Web Browser 4. FTP SettingViewing Live Images Viewing Still ImagesDisplaying a still image TroubleshootingSymptom Causes/Remedial Actions Image LinkOthers Specifications120 Template テンプレート