JVC VN-C205 manual Setting the Advance screen, Recording time, Recording files

Page 24

Settings (Step 2 Network Settings)

2-4 Other Settings Using the "VN-C205U Setup Tool" (5. Recordung Setting) (Continued)

Setting the [Frame Rate] screen

2To set the frame rate for local recording, select "Change the Recording Frame Rate during trigger recording", followed by selecting the frame rate accordingly.

Default frame rate is set at 10 fps. A frame rate of 10 fps for recording will be used when this box is not checked. (Set values: 30, 15, 10, 8, 6, 5, 4, 3, 2, 1)

Note

During local recording to CF cards, the frame rate is also dependent on the performance of the CF card in use. When the size of each recording file exceeds 8 MB (equivalent to a frame rate of 30 fps over a duration of about 8 seconds when the size of each image is 33 KB), frames may be dropped.

3For setting the recording time.

This can be set up to 30 seconds before and 60 seconds after the alarm input.

Cautions

[Before trigger] and [After trigger] values cannot be set to "0" at the same time.

Due to the memory capacity of VN-C205, recording time set for [Before trigger] and [After trigger] may differ from the actual maximum recording time.

(Example)

At a resolution of 640 x 480 (10 fps) when the size of each image is 40 KB, the actual maximum recording times are as follows:

Without CF card : 5 seconds before trigger / 10 seconds after trigger - 0 seconds before trigger / 15 seconds after trigger

With CF card : 20 seconds before trigger / 60 seconds after trigger

4For setting the priority.

Frame Rate : Priority is given to frame rate settings.

Recording Time : Frame rate is automatically adjusted such that recording can be performed according to the specified recording time.

46

Setting the [Advance] screen

5 For setting the recording action when the memory capacity of the CF card is full. One of the following actions can be selected. (Internal memory capacity is 8 MB.)

• Stop recording until an availability is made in the CF card.

• Remove old files that have exceeded a specific number of days. (If the number of days is set to "0", files will be deleted starting with the oldest one.)

Caution

When record setting that exceeds the recording capacity is performed with [Remove old files] set to "0 days", recorded files will not be retained. To retain the files, change the value for [Remove old files] or alter the record settings.

Notes

Recording time

While maximum recording time varies with the recording frame rate and image size, recording over a specified length of time may not be possible depending on the compression level and object.

Recording files

A trigger-recording file is created each time a trigger occurs. If successive triggers occur over a continuous period of time, these will be recorded into 1 file.

The maximum size of each recording file id 80 MB. Recording will stop upon exceeding 80 MB.

Caution

Loading local recording images to the PC

Rec files containing local recording images may also be uploaded automatically to the FTP server. (Page 50, "Rec File")

Perform the following procedure to load local recording images to the PC.

For saving local recording to the PC, follow the procedure below.

1 Select [Refer to Local Rec.].

2 Select the file to load.

3 Right-click on the selected file and select [Download to PC].

To obtain information on whether local recording has started, check the [Trigger] box on the [Recording] screen, followed by setting [Message] in [Alarm Setting] of the V.Networks Controller. (Page 63)

47

Image 24
Contents VN-C205INSTRUCTIONS VN-C205Not apply to all appliances Information for USASettings Contents IntroductionPreparation Settings OperationCharacteristics Operating PrecautionsIntroduction Latest Updates Operating Environment Name and Function of PartsVideo setting switch Preparation Procedure Connection ExamplesFlowchart of installation work for camera Getting Started InstallationAdjustment of the camera’s angle of view PreparationPreparation Connection/Installation Mounting the Camera to the CeilingPreparations Preparations  Connection to Alarm Input/Output Terminal  Inserting the CF cardConnect the alarm terminal Connect the input power supply cableConnect the LAN cable Point the camera in the direction you wish to captureAdjusting the iris level When installing the Camera to the electrical box Adjusting the focal lengthAdjusting the focus Settings related to videoInstalling the Software Pull out the cables aside and mountWhite-spot correction Setting PCs IP Address Windows XP Settings Network SettingsClick Select Internet Protocol TCP/IP and click PropertiesSetting PCs IP Address Windows For Windows 2000, set according to the following procedureSelect Settings and click Properties Set IP address toThis VN-C205U Setup Tool only allows connection of VN-C205 Check settingsFor other settings, next Click Start up the V.Networks Controller.Other Settings Using the VN-C205U Setup Tool Authorization Level Allowed AccessAll operations using the V.Networks Controller Viewing of motion images onlyOther Settings Using the VN-C205U Setup Tool 2. Multicast Perform area setting This section describes procedures for alarm setting Alarm InputOperation when an alarm input is activated Alarm 1/Alarm Detect ModeAlarm Output Alarm FTP Alarm Output Function/Set Value OutputOutput Set Values Output ValueSetting the Advance screen Recording timeRecording files Other Settings Using the VN-C205U Setup Tool 6. Web Other Settings Using the VN-C205U Setup Tool 7. FTP ServerStart up the VN-C205U Setup Tool and select FTP Server Displaying still images uploaded to the /user folderPassword Error recovery Connection errorTransfer error Alarm FTP Upload SettingStart up the VN-C205U Setup Tool and select Time When NTP is usedStart up the VN-C205U Setup Tool and select Memory Info Normal High SpeedConnect to VN-C205 Features that Allow Setting Using the V.Networks Controller Starting Up V.Networks ControllerSettings Setting Using the V.Networks Controller Select View Specify Image Size and Upside Down settingsMotion Detection Standby Image Size and InversionImage Quality Setting Operations Setting Using the V.Networks ControllerFrame Rate Alarm Setting Select Setting and Time Stamp Perform setting Select Setting and Property Perform settingWhen alteration is complete, click Time StampRecord/Stop Operations Operation Using the V.Networks Controller PlaybackPlay button Click Playback screen is displayedSnapshot Access Authorization Level Operating EnvironmentSetting Using the Web Browser Operations Operating Using a Web BrowserStarting Up the Web Browser Setting Using the Web Browser 1. Other Settings Setting Using the Web Browser 2. View Setting Setting Using the Web Browser 3. Alarm Setting Click to apply settings and to save the set values Alarm  Alarm OutSetting Using the Web Browser 4. FTP Setting Operations Setting Using the Web BrowserViewing Still Images Viewing Live ImagesTroubleshooting Symptom Causes/Remedial ActionsImage Link Displaying a still imageSpecifications OthersTemplate テンプレート 120